User manual RICOH MP9060A

[. . . ] Please backup (copy) all important data as protection against data loss. q q q PC DOS is a trademark of IBM Inc. MS-DOS, Windows, and Windows ® 95 are trademarks registered in the United States and other countries by the Microsoft Corporation. The company names and product names written in this manual are trademarks or registered trademarks. Conventions This manual uses the following symbols which indicate important information. Ignoring this warning and incorrect handling may result in serious personal injury or damage to the product. [. . . ] Drives that support Packet Write. <<Contents Specifications Drive | Disc Drive : MP9060A Type Interface Data buffer memory Data transfer speed CD-R/CD-RW Write/Read speed (Ave. ) 24X: 20X: 20X: 8X: 8X: 6X: 6X: 4X: 4X: 2X: 2X: 1X: 1X: 3. 60 MB/sec. (Mode2, From2) Internal type (bare drive) Enhanced-IDE (ATAPI) 2MB 16. 6MB/sec. (Max. ) DVD-ROM Read speed Average access time Initial processing time 4X: 5. 5 MB/sec. or less horizontal/vertical Format CD-DA CD-ROM CD-Extra CD-ROM XA Photo CD*3 CD-i*3 CD-ROM + CD-DA Video-CD CD-Text Write Read Play*2 Mounting direction Compatible formats * * * * * * * * * * * * * * * * * * * * * * * Loading system Power Power consumption Tray type (automatic loading/eject) DC5V, DC12V 12w max. 148. 4 X 198(included front panel) X 42. 5mm Error Rate: MTBF: MTTR: Temperature Humidity Vibration Shock Environmental dust 10-12 bits or less 100, 000hours or greater Within 30 minutes When operating When not operating 5°C to 40°C (No air cooling) -30°C to 65°C 55% to 90% R. H. (No condensation) (No condensation) 0. 035mmpp(10 to 45Hz) 1 X 9. 8 m/s2 0. 025mmpp(45 to 65Hz) (5 to 300Hz) 0. 2 X 9. 8 m/s2 (65 to 150Hz) 2 2 X 9. 8 m/s 40 X 9. 8 m/s2 (11msec. half sine) Class 3 million or less (3 million particles of 0. 5 micron dustper cubic foot or less) Environmental Conditions *1 Speed is automatically reduced if reading is unsuccessful. Also, Photo-CD requires a license from Kodak. The drive's appearance and specifications may change without notice. Disc CD-R Characteristic External diameter Dimensions Internal diameter Thickness Recording area (User area) Time Recording capacity Track pitch Substrate material Recording material Reflectance (R to p) Eccentricity Maximum camber angle Recommended recording power Playback power Playback stability Environment for use Storage life Capacity Linear speed 80min. *1 700MB 1. 2m/s CD-R ø120mm ø15mm 1. 2mm ø50 to 116mm 74min. 650MB 1. 2m/s 1. 6 ± 0. 1µm Polycarbonate Organic pigment (phthalocya-nine) / Au or Ag lamination (Organic protective layer attached) 65% or more 70µm or less 0. 4° or less 6 to 7mW(at É:785nm, NA:0. 5) 1mW or less 106times or more (Playback power = 0. 7mW) -5 to 55°C 5 to 95%RH 100 years or more 5 to 25°C, 5 to 60%RH Avoiding direct sunlight) 63min. 550MB 1. 4m/s CD-RW CD-RW ø120mm ø15mm 1. 2mm ø50 to 116mm 74min. Caution Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. 5. Power Connector Connects to the power supply (5 and 12V DC) of the host computer. Connecting the wrong way may damage the system (and is not guaranteed). << Contents Emergency Eject This drive has a function that allows the CD to be ejected manually, if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Pull the front door to open it all the way, then grip the disc tray between thumb and forefinger and gently pull it straight out. Note If you cannot get a good grip on the disc tray with your fingers, use a steel binder clip or spring clamp to pull it out. Back Next Load the disc | Disc ejection | Emergency Eject Using the Drive in a Vertical Position << Contents Disc ejection 1. Press the eject button or push the disc tray and the tray will be inserted back into the drive. Caution After ejecting the disc, return the disc tray inside the unit quickly. When the disc tray is in the ejected position, dust and other debris will enter, possibly causing read errors, write errors, or drive failure. Back Next Load the disc |Disc ejection | Emergency Eject Using the Drive in a Vertical Position << Contents Load the disc 1. Place the disc on the disc tray. Be careful not to touch the recording surface of the disc. 3. Load the disc by pressing the eject button or by lightly pushing in the disc tray. Next Load the disc | Disc ejection | Emergency Eject Using the Drive in a Vertical Position << Contents Using the Drive in a Vertical Position The drive can be installed in a vertical position. When loading a disc, insert it into the inner side of the tabs. Back Load the disc | Disc ejection | Emergency Eject Using the Drive in a Vertical Position << Contents Installing the Drive Specific knowledge of hardware and software is necessary to install the drive. We cannot guarantee against direct or indirect damage resulting from improper connections. [. . . ] Audio digital output The drive supports S/PDIF(IEC958) for digital audio output. As long as the sound board comes with S/PDIF input, it can be connected externally to the D/A converter. The drive can be used as a CD transporter for playing CDs at the desired sound quality level. MP9060A When L, R Sound Card Motherboard Primary or Secondary Back Next 1. [. . . ]