User manual RICOH MP9120A

[. . . ] The volume that exceeds 70dB occurs and the obstacle sometimes breaks out. Declaration of Conformity "The Product complies with the requirements of the EMC Directive 89/366/EEC and the Low Voltage Directive 73/23/EEC. " q Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to inappropriate installation or handling, or direct or indirect damages. Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. q q q q q q PC DOS is a trademark of IBM Inc. [. . . ] The disc written using the CD-R/RW drive may not be readable by CD-ROM drives. Even if it is the recommendation disc, some of discs may have possibility to fail writting with highest writting speed with the problem on the disc. In this case, please try to write with lower writting speed, or please try to use another disc. Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Write. Front Panel Rear panel Front Panel 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. This might cause damage to the loading section of the drive. 2. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Sudden loud noises can damage your hearing. 4. Busy indicator This indicator lights orange when a disc is mounted into the drive. If a disc is not mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually for an emergency case such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Rear panel 1. Digital Audio (SPDIF) Output Connector Provides output to a sound card (Digital signal). * No digital audio cable is included with the MP9120A. 2. Analog Audio Output Connector Provides output to a sound card (Analog signal). 3. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 4. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Caution Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. 5. Power Connector Connects to the power supply (5 and 12V DC) of the host computer. We cannot guarantee against direct or indirect damage resulting from improper connections. Ask your supplier for details of the installation procedure. Before Installation Before installing the drive, please note the following points. q You will need the following: r A Phillips head screw driver of a suitable size to fit the securing screws for the drive unit. r The manual for the computer, to know the location of the IDE connector. q Turn off all peripheral devices of the computer, and the computer itself, and disconnect their power cords from the wall sockets. [. . . ] Device Drivers Caution When using CD-ROM discs, DVD-ROM discs, CD-R discs or CD-RW discs, do not attach any stickers or labels to the discs. Using discs with labels attached not only causes read and write errors, but data on the disc may be lost due to damage to the disc itself. q q q q Load the disc Disc ejection Emergency Eject Using the Drive in a Vertical Position Drive : MP9120A Type Interface Data buffer memory Data transfer speed CD-R/CD-RW/High Speed CD-RW Write/Read speed (Ave. ) Internal type Enhanced-IDE (ATAPI) 2MB 33. 3MB/sec. (Max. ) (PIO4, DMA2) 32X: 24X: 12X 12X: 10X 10X: 8X: 8X: 4X: 4X: 2X: 2X: 8X: 4. 8MB/sec. (MAX) DVD Read speed Average access time Initial processing time 100msec. [. . . ]