User manual RICOH MP9200A

[. . . ] The volume that exceeds 70dB occurs and the obstacle sometimes breaks out. Declaration of Conformity "The Product complies with the requirements of the EMC Directive 89/366/EEC and the Low Voltage Directive 73/23/EEC. " q Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to inappropriate installation or handling, or direct or indirect damages. Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. q q q q q PC DOS is a trademark of IBM Inc. [. . . ] *2 The speed at which to write on the current standard CD-RW discs is 4x recording (at a data transfer rate of 600KB/second). q q q q q q q q q q Explains the system environment required for using the drive as a CD-R/CD-RW drive. PC Operating System IBM PC/AT compatible Windows Me/98/95(ORS2 or later) Windows NT Workstation Ver. 4. 0 (Service Pack 5) or later Windows 2000 (Professional) Pentium 166 MHz or higher (When using JustLink) 64MB or more Hard disk with average access time of 19msec or less, and data transfer speed of 1, 200KB/sec or greater. Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required discs*2 Recommendation Tested to be compatible Taiyo Yuden, Mitsui Chemicals, Mitsubishi CD-R Ricoh Chemical, Maxell CD-RW Ricoh Mitsubishi Chemical*1 High Speed CD-RW Ricoh Mitsubishi Chemical CPU Memory Hard disk Interface Drive bay Power Recommendation *1 *2 The disc written using the CD-R/RW drive may not be readable by CD-ROM drives. Even if it is the recommendation disc, some of discs may have possibility to fail writing with highest writing speed with the problem on the disc. In this case, please try to write with lower writing speed, or please try to use another disc. Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Write. Front Panel Rear panel Front Panel 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. This might cause damage to the loading section of the drive. 2. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Sudden loud noises can damage your hearing. 4. Busy indicator This indicator lights orange when a disc is mounted into the drive. If a disc is not mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually for an emergency case such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. When the disc tray is in the ejected position, dust and other debris will enter, possibly causing read errors, write errors, or drive failure. Back Load the disc Emergency Eject Next Disc ejection Using the Drive in a Vertical Position Load the disc 1. Place the disc on the disc tray. Be careful not to touch the recording surface of the disc. 3. Load the disc by pressing the eject button or by lightly pushing in the disc tray. Next Load the disc Emergency Eject Disc ejection Using the Drive in a Vertical Position Using the Drive in a Vertical Position The drive can be installed in a vertical position. Cannot be used with business card CDs. Back Load the disc Emergency Eject Disc ejection Using the Drive in a Vertical Position Specific knowledge of hardware and software is necessary to install the drive. We cannot guarantee against direct or indirect damage resulting from improper connections. Ask your supplier for details of the installation procedure. Before Installation Before installing the drive, please note the following points. q You will need the following: r A Phillips head screw driver of a suitable size to fit the securing screws for the drive unit. r The manual for the computer, to know the location of the IDE connector. [. . . ] Device Drivers Caution When using CD-ROM discs, DVD-ROM discs, CD-R discs or CD-RW discs, do not attach any stickers or labels to the discs. Using discs with labels attached not only causes read and write errors, but data on the disc may be lost due to damage to the disc itself. q q q q Load the disc Disc ejection Emergency Eject Using the Drive in a Vertical Position Drive : MP9200A Type Interface Data buffer memory Data transfer speed CD-RW/High Speed CD-RW Write/Read speed (Ave. ) Internal type Enhanced-IDE (ATAPI) 2MB 33MB/sec. (Max. ) (Ultra DMA mode2) Read Speed 4X: 8X: 20X: 32X: 40X: Write Speed CD-R: 4X: 8X: 12X: 16X: 20X: CD-RW: 4X: 10X: DVD Read Speed: 12X: 600KB/sec. 16. 5MB/sec. (MAX) Caution When the 20X write speed is specified, data is written at 16X from the innermost track to about the 70 MB position, and at 20X from positions exceeding 70 MB up to the outermost track. [. . . ]