User manual STRONG SRT 4402

[. . . ] Safety Instructions · Be sure to read this User's Manual before starting the operation of the receiver · Never open the cover. It is dangerous to touch the inside of the receiver due to possible electric hazard. · When the receiver is unused for a long time, unplug the power cord from the wall outlet. · Do not use a damaged power cord that may cause a fire or an electric shock. [. . . ] Connect the OUT connector of the DiSEqC 1. 0 switch to the LNB IN connector at the back of your receiver. Figure 7. Connecting multiple fixed dishes to your receiver using a DiSEqC 1. 0 switch 13 14 Connecting to Dish Connecting to CI Module <Connecting a dish on a motorized positioner to your receiver> 3. 3 Connecting to CI Module(CI Model Only) Another possibility to watch program from multiple satellites is by mounting a dish to a motorized DiSEqC 1. 2 positioner. Have your t dealer mount the dish to the positioner, set the or react azimuth(angle of elevation) and let him set the center point for your positioner. Connect the LNB with a coax cable to the LNB IN connector of the positioner, and connect the OUT connector of the positioner to the LNB IN connector at the back of your receiver. Insert CI module into CI slot for watching TV program from Service Provider. Do no plug in/out CI module when the receiver is powered on. But you can insert smart card to CI module with power on. Figure 9. Connecting a dish on a motorized positioner to your receiver Figure 10. Connecting to CI Module 15 16 Connecting to CI Module 3. 4 Connecting to SMART CARD Insert Smart Card into Smart Card slot for watching TV program from Service Provider. Setting and Operations 4. 1 Before Settings <Starting up for the First Time> 1. If it is first time using a receiver, you should set parameters for system configuration. Connecting to SMART CARD Warning <screen 1> <Menu Information> The menu consists of main-menu and sub-menu, as you see in the <Screen 1>. Main-menu has items and each main-item has its sub-menu items. <screen 2> 17 18 Setting and Operations 4. 2 Basic Settings To install the receiver properly you have to perform Antenna Setup. When you have finished the setup procedure, you can start watching TV or is turning to Radio. From the main-menu<Screen 1>, press the OK button on the Installation to display sub-menu. <Screen 2> <DiSEqC 1. 2 Setup> If you use positioner Antenna, you can set East/West limit of your dish in the DiSEqC 1. 2 SETUP menu at first. And then, <Screen 3> will appear as displayed below. Setting and Operations 2. If you selected "on" item of ON/OFF mode, you can setup position. Press EXIT to cancel edit, and press OK on the edit field or press MENU on the keypad box to confirm edit. <screen 7> Before start to scan antenna, you should set values of antenna configuration parameters. <screen 9> 21 22 Setting and Operations 5. <Screen 7> Setting and Operations <Manual Scan> You can scan TP frequency and channel manually in the Manual Scan menu. Press the OK button in the Manual Scan menu of Installation. <screen 6> <screen 10> Press the OK button to scan the selected transponder. You can change polarity, frequency and symbol rate of a transponder, and edit transponder-name by pressing OK at "TP Name" field. If you want delete TP, Press BLUE button in RCU. <screen 12> First, select the satellite name in the "Satellite" item. Select or enter the accurate value frequency, polarization, symbol rate. Also you want to channel scan, Press the button and change to "channel scan" on the "scan mode" field. <Screen 13> <screen 11> If you want Insert TP, Press RED button in RCU. [. . . ] If you press the OK button on Parental Lock menu item, the following window will appear, In the window, you are requested to enter Current PIN, New PIN and Retype PIN for confirmation. Setting and Operations <System Information> Shows the system information including the Firmware version and model name. <screen 28> <Factory Reset> <screen 26> Resets the parameters of the receiver to the factory default setting. <Calendar> Factory Reset will erase all installed data, use this function carefully. <screen 27> 33 34 Setting and Operations <Smart Card> You can navigate the menu, which is provided by Smart Card module. This information varies a lot depending on the service provider. Trouble Shooting A. 1 Trouble Shooting There may be various reasons for the abnormal operation of the receiver. If the receiver does not work properly after checking it, please contact the dealer. [. . . ]