User manual THOMSON ROC 26

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual THOMSON ROC 26. We hope that this THOMSON ROC 26 user guide will be useful to you.


THOMSON ROC 26 : Download the complete user guide (2243 Ko)

You may also download the following manuals related to this product:

   THOMSON ROC 26 (2610 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)
   THOMSON ROC 26 DESSIN (490 ko)

Manual abstract: user guide THOMSON ROC 26

Detailed instructions for use are in the User's Guide.

[. . . ] F (FF) : fast forward for VCRS and DVDS; press with blue key for fast text function in TV mode. B (PLAY): plays a VCR tape or DVD disk; press with yellow key for fast text function in TV mode. K (PAUSE): Suspends play and stops on an image; press with magenta key for fast text function in TV mode. i/EXIT: Teletext Off in TV mode; turns off the menu of the selected product (SHIFT + EXIT). [. . . ] If the product doesn't turn off, repeat step 2, using the next 3-digit code in the list. Checking the programming: Your product should be ready to receive remote control commands. If none of the codes work, you may still be able to retrieve the appropriate code. Hold down the S key (17) until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). Press the product key (2) that corresponds to the type of product you want to control: TV: television set, VCR: video recorder. Point the remote control towards the product and try to turn it off by pressing the B key (11). If the product you want to control turns off, press OK (8) to save the subcode. If the product does not turn off, press the B key (11) until the product switches off (up to 200 times). Wait approximately one second between key presses to give the red indicator lamp (1) enough time to go off and light up again. Immediately upon turning off the product to be controlled, press OK (8) to save the code. Note: If you want to assign another type of product than those mentioned on the remote control, begin by entering a code that corresponds to the product you want to programme (a 3-digit code that you will find in the code booklet ­ see method B). Example: if you want to control a satellite receiver with the VCR key, begin by entering a satellite code (any satellite, for example: 603 for a Thomson satellite receiver) then begin the procedure. Checking the programming: Your product should be ready to receive remote control commands. With this method, the remote scrolls through the full code list by sending an IR signal to the product to be controlled remotely. Hold down the S key (17) until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). Press the product key (2) corresponding to the type of product you want to control: (for example TV). After a few seconds, the remote begins to scroll through the code list at approximately 1 code per second. Press PROG+ (16) once again to slow down the test speed (1 code every 3 seconds). [. . . ] Hold down the S key (17) until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). The indicator light will blink and then go off for about 8 seconds before blinking once more and then staying off. If the remote previously controlled the television volume in SAT mode, it will now control the volume of the satellite receiver; if it previously controlled the volume of the satellite receiver, it will now control the television volume. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE THOMSON ROC 26




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual THOMSON ROC 26 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.