User manual THOMSON ROC 4406B

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual THOMSON ROC 4406B. We hope that this THOMSON ROC 4406B user guide will be useful to you.


THOMSON ROC 4406B : Download the complete user guide (3896 Ko)

Manual abstract: user guide THOMSON ROC 4406B

Detailed instructions for use are in the User's Guide.

[. . . ] Hold down the SETUP key until the red indicator lamp remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). Press the key that corresponds to the type of equipment you want to control: TV, DVD/VCR. Direct the remote control towards the set and try to switch it off by pressing the B key. [. . . ] Method B ­ 4-digit codes Programming Before you start programming, you must find the code of the set to be controlled. Hold down the SETUP until the red indicator lamp remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). Press the key that corresponds to the type of equipment you want to control: TV, DVD/VCR. While the indicator is lit, enter the first digit of the 4-digit code proposed for the set to be controlled (example: 0036 for Thomson). The red indicator then goes off if the code is correct or flashes, if the code is not on the list. Direct the remote control towards the set and try to switch it off by pressing the B key. Check of the programming: In principle, your set is ready for receiving the remote control commands. Check your remote control for proper functioning by performing the test described on page 3. Note: If you want to assign another type of product than those mentioned on the remote control, begin by entering a code that corresponds to the product you want to programme (a 4-digit code that you will find in the code booklet ­ see method B). Example: if you want to control a satellite receiver with the DVD/VCR key, begin by entering a satellite code (any satellite, for example: 0603 for a Thomson satellite receiver) then begin the procedure. Hold down the SETUP until the red indicator lamp remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). Press the TV key, then follow one of the programming methods (A, B, C or D) described earlier. If a second code programming is required, then repeat steps 2 and 3 above. Adjustment of ALL volume controls under a specific mode You can allocate the volume control to one of the modes of the remote control on condition that the volume control exists on the corresponding device (e. ) corresponding to the device whose volume will always be controlled by the VOL and c keys. Adjustment of the volume controls for EACH mode You can decide that the volume control is functional for each mode selected on condition that the volume control exists on the corresponding device (e. Control of the television set sound in TV mode, the control of the sound of the SAT receiver in SAT mode, . ) corresponding to the device whose volume will always be controlled by the VOL and c keys. Hold down the SETUP until the red indicator lamp remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). [. . . ] In the DVD/VCR position, make sure that the AV mode is activated for the TV set (the SCART socket must be selected). If this light goes out, you have to press the SETUP key again before using the navigation keys. - For a television or a satellite receiver: switch on and, for example, press PROG+ to change channels. Try other remote control keys to find out the range of functions you can control. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE THOMSON ROC 4406B




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual THOMSON ROC 4406B will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.