User manual THOMSON ROC 3407 CODE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual THOMSON ROC 3407. We hope that this THOMSON ROC 3407 user guide will be useful to you.


THOMSON ROC 3407 CODE: Download the complete user guide (344 Ko)

You may also download the following manuals related to this product:

   THOMSON ROC 3407 (2721 ko)
   THOMSON ROC 3407 (1007 ko)
   THOMSON ROC 3407 (1007 ko)
   THOMSON ROC 3407 (1007 ko)
   THOMSON ROC 3407 (1007 ko)
   THOMSON ROC 3407 (1007 ko)
   THOMSON ROC 3407 (1007 ko)
   THOMSON ROC 3407 (1007 ko)

Manual abstract: user guide THOMSON ROC 3407CODE

Detailed instructions for use are in the User's Guide.

[. . . ] The indicator lamp flashes to signal that this time is almost up, and then goes off). Direct the remote control towards the set and try to switch it off by pressing the key G. If the set you want to control switches off, press OK to memorise the code. Should the set not switch off, press key G repeatedly, until the set switches off. [. . . ] Between pressing the keys, be sure to leave enough time for the indicator light to go out and then relight (about 1 second). Proceeding this way will enable you to see whether the set responds or not. Check of the programming: In principle, your set is ready for receiving the remote control commands. Check your remote control for proper functioning by performing the test described on page 2. Direct the remote control towards the TV set and try to switch it off by simply pressing the key G. If the device does not turn off, you must program the remote control using one of the methods A, B, C or D described hereafter. Before you start programming, you must find the code of the set to be controlled. Hold down the SETUP key until the red indicator light blinks and then remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes to signal that this time is almost up, and then goes off). While the indicator is lit, enter the first digit of the 4-digit code proposed for the set to be controlled (example: 0036 for Thomson). If you think that not all of the keys are active, repeat the procedure of this programming method to find out the code supporting a wider range of features. Method D ­ Automatic code search With this method, the remote control scrolls through the full code list by sending an IR signal to the set to be controlled remotely. Hold down the SETUP key until the red indicator light blinks and then remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes to signal that this time is almost up, and then goes off). After a few seconds, the remote control begins to scroll through the whole code list included in the library (at a rate of roughly 1 code per second). Press the P+ , G key once again to slow down the test speed (1 code every 3 seconds). As soon as the set changes channels (or turn off, or start to play the disk), you must press OK to save the code and stop the remote control scrolling through the list. If you do not react quickly enough, you can go back to the previous code by pressing P- as many times as necessary (you can go forward by pressing G , P+ if you have gone back too far). Hold down the SETUP key until the red indicator light blinks and then remains lit. Press the number keys (0 to 9) until you notice that the indicator lamp blinks once. [. . . ] Press the number keys (0 to 9) until you notice that the indicator lamp blinks once. The number which made the indicator lamp blink is the first of the four figures comprising your code, write it down. Conservez cette notice et la liste des codes séparée afin de pouvoir reprogrammer ultérieurement la télécommande pour commander d'autres appareils. For a television or a satellite receiver: switch on and, for example, press 2 to change channels, etc. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE THOMSON ROC 3407




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual THOMSON ROC 3407 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.