User manual THOMSON VTH6050G

[. . . ] E Important Précau tion INSTAL LATION confor - Assur me appare à celle indiqu ez-vous que il. chaleu Installez le ée sur l'étiqu la tension-sect r magné importante magnétoscop ette d'identificati eur de votre tiques habita à la chaleu ou électri(cheminée. . . e horizontalem on, située ) ou à l'arrièr tion est ques ent, r. isant de de mmen et 7 cm Laissez 10 t d'espa ale ambiante cet appare des champ cm minim ce autour ne doit il sont sensib s pas dépass um au minimum de dessus pas dépass les pour . [. . . ] ð Wait for quite a long time (up to 15 minutes), until a message tells you that storage of your satellite channels is completed. 12 Refer to page 5 to sort your satellite channels and check their names. J Some satellite receiver models cannot be controlled by your video recorder. In that case, you'll have to programme both sets separately for timer-controlled recording. 8 connecting the recorder to a J Whenselect the socket videoduring set-up. television set with integrated satellite receiver, you must AV1 Set-up Other sets to call up the control J Press the STATUS keyAV2, AV3 or AV4 withscreen and select the socket AV1, key AV of the remote control. Sockets AV1 / AV2 / AV3 / AV4 GB AV2 Decoder AV1 / AV2 DVD Camcorder Other video recorder AV4 Audio/Video or Dolby Pro Logic amplifier The two cinch sockets AUDIO OUT (red and white) and the cinch socket VIDEO OUT (yellow) enable you to connect your video recorder to an Audio/Video amplifier. TV set Satellite receiver Video disk player The pictures from another set operating in the play mode and connected to AV2 are conveyed to the socket AV1. When your television is connected to this socket, you can watch the pictures from the set connected. AV3 (depending on the model) Hi-Fi system The two cinch sockets AUDIO OUT (red and white) enable you to connect your video recorder to the Hi-Fi stereophonic system. Thus, you'll be able to reproduce all the sound effects of your tapes (musicals, films. . . ) on your Hi-Fi system. Camcorder Connect your camcorder to the sockets AUDIO L (left), AUDIO R (right), VIDEO and CAM/PAUSE (if your camcorder is fitted with such a socket). Select Au 3 on your video recorder. J With compatible camcorders, the PAUSE socket facilitates copying by triggering the recording mode of the video recorder as soon as the camcorder switches over from PAUSE to PLAY. The video recorder must be switched on Record Pause. "DOLBY", "Prologic" J Licensing Corporation. and the double-D symbol are trademarks of DOLBY Laboratories 9 Use Using the remote control control to operate J Your remotetelevision enables you leaving yourthe video recorder or set without seat. All you have to do is to press either key VCR for the video recorder or TV for the television. For the television set, you'll have to programme the remote control as explained below. Brand of your TV set Brand code BRANDT . . 001-000-002-010-020 Other makes: see page 21 Controlling the video recorder 1 recorder. Press key VCR to control your video 18 To switch over to another channel. 19 To select a channel. For 2-digit channels, first press 0/-(0, 1, 2 for Pr12). 3 To switch your video recorder on and off. 9 to 13 To navigate through the menus and validate with OK. 20 To mark an index. 29 Recording. To select the units connected to the 14 To exit a menu at any time. 15 To call up the SUMMARY menu. Programming the remote control with the TV code J 1 2 3 Your remote control can be used to control some functions of most television sets. To this end, you must programme it with one of the codes provided in the table below or on page 21 of this user manual. Press key TV on the remote control. Hold down key MENU (15) and enter the three-digit code corresponding to the make of your television set (see the code table below). Release key MENU (15) and try to control the television set. The codes depend on the television model. When you replace the batteries of the remote control, you have to programme it again J Controlling the television set 2 Press key TV to control your television set. 4 These keys have the same functions as the to corresponding keys of the remote control of your television set (when the latter is of our 15 make). [. . . ] With this function activated, you may obtain a beep sound any time you press a key (of the remote control or video recorder). To change the language of the OSD menus (French, English, German, Italian. . . depending on the model). Beep sound J J Language 19 Use Other functions functions explained enable you to J The video recorder, playon this pagecontinuously, lock the or record play NTSC tapes, and counter reset. ntrol The remote co doesn't work?Press key VCR Electronic key J 1 2 3 To prevent the video recorder from being used, keys on the front can be locked. Press key B (3) on the remote control until the indication CL comes up on the video recorder display. [. . . ]