User manual TP-LINK TL-R4000+

[. . . ] TL-R4000+ Load Balance Broadband Router Rev: 1. 0. 1 1910010032 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. All rights reserved. http://www. tp-link. com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. [. . . ] If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer. Start IP Address - This field specifies the first of the addresses in the IP address pool. End IP Address - This field specifies the last of the addresses in the IP address pool. Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the router with their current dynamic IP address. Enter the amount of time, in minutes, which the user will be "leased" this dynamic IP address. Default Gateway - (Optional. ) Suggest to input the IP address of the LAN port of the router, default value is 192. 168. 1. 1 Default Domain - (Optional. ) Input the domain name of your network. Primary DNS - (Optional. ) Input the DNS IP address provided by your ISP. Secondary DNS - (Optional. ) Input the IP address of another DNS server if your ISP provides two DNS servers. Note: To use the DHCP server function of the router, you must configure all computers on the LAN as "Obtain an IP Address automatically" mode. 4. 5. 2 DHCP Clients List This page shows Client Name, MAC Address, Assigned IP and Lease Time for each DHCP Client attached to the router (Figure 4-17): - 28 - TL-R4000+ Enterprise Broadband Router User Guide Figure 4-17 DHCP Clients List ID - The id of the DHCP Client Client Name - The name of the DHCP client MAC Address - The MAC address of the DHCP client Assigned IP - The IP address that the router has allocated to the DHCP client. Before the time is up, DHCP client will request to renew the lease automatically. To update this page and to show the current attached devices, click on the Refresh button. 4. 5. 3 Address Reservation When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time it accesses the DHCP server. Reserved IP addresses should be assigned to servers that require permanent IP settings. This page is used for address reservation (shown in Figure 4-18). Figure 4-18 Address Reservation MAC Address - The MAC address of the PC of which you want to reserve IP address. Assigned IP Address - The IP address of the router reserved. To Reserve IP addresses: 1. Enter the MAC address (The format for the MAC address is XX-XX-XX-XX-XX-XX. ) and IP address in dotted-decimal notation of the computer you wish to add. - 29 - TL-R4000+ 2. Enterprise Broadband Router User Guide Click the Save button when finished. To modify A Reserved IP address: 1. Click the Save button Click the Next button to go to the next page and Click the Previous button to return the previous page. Note: The function won't take effect until the router reboots. 4. 6 Forwarding Figure 4-19 Forwarding menu There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. 4. 6. 1 Virtual Servers Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and FTP. A virtual server is defined as a service port, and all requests from Internet to this service port will be redirected to the computer specified by the server IP. [. . . ] To change the WEB management port number: Login to the router, click the "Security" menu on the left of your browser, and click "Remote Management" submenu. On the "Remote Management" page, type a port number except 80, such as 88, into the "Web Management Port" field. Click "Save" and reboot the router. 2) Figure A-6 Note: Remote Management If the above configuration takes effect, to configure to the router by typing http://192. 168. 1. 1:88 (the router's LAN IP address: Web Management Port) in the address field of the web browser. 3) Login to the router, click the "Forwarding" menu on the left of your browser, and click the "Virtual Servers" submenu. [. . . ]