User manual TP-LINK TL-R4199G

[. . . ] TL-R4199G SMB Broadband Router Rev: 1. 0. 3 1910010054 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. Other brands and product names are trademarks or http://www. tp-link. com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Note: 6) 7) If you want to add more than one reserved IP, please go to step 1 to continue. It is possible that you configure more than one type of available service on a computer or server, it means the IP addresses for the virtual servers are same. Other configurations for the entries as shown in Figure 4-21: Click the Delete button to delete the entry. Click the Previous button to view the information in the previous screen, click the Next button to view the information in the next screen. Note: If you set the virtual server of the service port as 80, you must set the web management port on System Tools ­> Remote Management screen to be any value except 80 such as 8080. Or else there will be a conflict to disable the virtual server. 4. 5. 2 Port Triggering Choose menu "ForwardingPort Triggering", you can view and add port triggering in the next screen (shown in Figure 4-22). Some applications require multiple connections, like Internet games, video conferencing, Internet calling and so on. Port Triggering is used for some of these applications that can work with an NAT router. 32 TL-R4199G SMB Broadband Router User Guide Figure 4-22 Trigger Port - This displays the port for outgoing traffic. An outgoing connection using this port will "Trigger" this rule. Trigger Protocol - This displays the protocol used for Trigger Ports, either TCP, UDP, or All (all protocols supported by the router). Incoming Ports - This displays the port or port range used by the remote system, they are used for responding to the outgoing request. A response using one of these ports will be forwarded to the PC that triggered this rule. Incoming Protocol - This displays the protocol used for Incoming Ports Range, either TCP or UDP, or ALL (all protocols supported by the router). Enabled means that the rule will take effect, Disabled means that the rule will not take effect. Once configured, the operation for Port Triggering will proceed as follows: Step 1: A local host makes an outgoing connection using a destination port number defined in the Trigger Port field. Step 2: The router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. Step 3: When necessary, the external host will be able to connect to the local host using one of the ports defined in the Incoming Ports field. To add/modify a port triggering entry: Step 1: Click Add New. . . /Modify shown in Figure 4-22, you will see a new screen shown in Figure 4-23. Step 2: Select the application you want from the "Common Applications", then the Trigger port and Incoming ports will be added to the corresponding field automatically, you only need to configure the Trigger protocol and Incoming Protocol for the entry; If the "Common Applications" does not contain the applications that you want, please configure these options manually. 33 TL-R4199G SMB Broadband Router User Guide Figure 4-23 Step 3: After that, select Enabled to make the entry take effect. Note: 1) 2) 3) 4) If you want to add more than one reserved IP, please go to step 1 to continue. When the trigger connection is released, the according opening ports will be closed. Incoming Port Range cannot overlap each other. Other configurations for the entries as shown in Figure 4-23: Click the Delete button to delete the entry. [. . . ] Otherwise, you can select "Connect Automatically" for Internet connection mode. Figure B-2 Note: 1) 2) Sometimes the connection can not be disconnected although you specify a time to Max Idle Time, because some applications still visit the Internet continually in the background. If you are a Cable user, please configure the router following the above steps. 72 TL-R4199G 2. SMB Broadband Router User Guide How do I configure the router to access Internet by Ethernet users? Step 1: Login to the router, click the menu NetworkWAN on the left of your browser, On the WAN screen, select "Dynamic IP" for "WAN Connection Type", and finish it by clicking Save. Step 2: Some ISPs require that you register the MAC address of your adapter, which is connected to your cable or DSL modem during installation. If your ISP requires MAC register, login to the router and click the menu NetworkMAC Clone. [. . . ]