User manual TP-LINK TL-SF1008P

[. . . ] http://www. tp-link. com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Identifying External Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Appendix A: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Package Contents The following items should be found in your box: One TL-SF1008P 8-port 10/100M Desktop PoE Switch One DC Power Adapter Four rubber cushions to be used under the switch This User Guide Note Make sure that the box contains the above items. If any of the listed items are damaged or missing, please contact with your distributor. Chapter 1. PoE Switch. Introduction of the Product Thank you for choosing the TL-SF1008P 8-port 10/100M Desktop 1. 1 Overview of the Product The TL-SF1008P 8-port 10/100M Desktop PoE Switch provides the seamless network connection, which integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities. Four of the eight Auto-Negotiation RJ45 ports (port-1~port-4) on the switch support Power over Ethernet (PoE*) function, which can automatically detect and supply power with those IEEE 802. 3af-complaint powered devices (PDs*). 1 *PSE: a device (switch or hub for instance) that will provide power in a PoE setup. *PoE: This technology describes a system to transmit electrical power, along with data, to remote devices over standard twisted-pair cable in an Ethernet network. Examples include powering IP telephones, wireless LAN access points, network cameras, network hubs, embedded computers etc. 1. 2 Convention The Switch or TL-SF1008P mentioned in this User Guide stands for TL-SF1008P 8-port 10/100M Desktop PoE Switch without any explanation. 1. 3 Features Complies with IEEE802. 3, IEEE802. 3u, IEEE802. 3af standards 8 10/100Mbps Auto-Negotiation RJ45 ports with 4-port PoE function (port-1~port-4), all of them support Auto-MDI/MDIX Supports PoE power up to 15. 4W for each PoE port Supports PoE power up to 53W for PoE ports Supports PoE IEEE802. 3af compliant PDs Supports IEEE802. 3x flow control for Full-duplex Mode and backpressure for Half-duplex Mode 1K entry MAC address table of the TL-SF1008P with autolearning and auto-aging 2 LED indicators for monitoring power, link, activity and speed External power adapter supply Chapter 2. Installation During the installation procedure, please only use the accessories equipped with the switch. 2. 1 Mounting the Switch on a Desk To install the Switch, please follow the steps: 1) You can place the Switch on a flat desk. 2) Please insert the power adapter carefully to the power socket of the switch, and then connect it properly to a power source through the cable of the switch. 3) Ensure adequate ventilation space around the switch for dissipating heat and air. 2) Make sure the power is off before unplugging the power adapter. 3 2. 2 Power On The TL-SF1008P Switch can be used with DC power supply. Powering on the Switch, it will automatically initialize and its LED indicators will respond as follows: 1) All the LED indicators except PoE ports LED will light synchronously at first, then all of them included Link/Act LED (green), 100Mbps LED (green) and PoE MAX LED (red), will light off at once, which indicates the system initialized well. Note If the LED indicators don't respond as described above, please check the power supply and its connection. Chapter 3. Identifying External Components This Chapter describes the front panel, rear panel and LED indicators of the Switch. 3. 1 Front Panel Figure 3-1 TL-SF1008P Switch Front Panel The Switch's LEDs are located on the front panel. 4 Name Power Status On(green) Off On(green) Indication Power on. There is a PoE PD connected to the port, which supply power successfully. The PoE power circuit may be in short, or the power current may be over that of the PD's classification. [. . . ] Once the network devices are connected to these 8 ports through the network cable, the switch will make them plug and play according to the Auto-MDI/MDIX detection. The working status can be indicated by the corresponding LEDs on the front panel. [. . . ]