User manual TP-LINK TL-WA801ND

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. [. . . ] Universal Repeater - In Repeater mode, the AP with WDS enabled will relays data to an associated root AP. The wireless repeater relays signal between its stations and the root AP for greater wireless range. WDS Repeater - In Universal Repeater mode, the AP with WDS disabled will relays data to an associated root AP. The wireless repeater relays signal between its stations and the root AP for greater wireless range. Wireless Name of Root AP - If you select the radio button before Wireless Name of Root AP, the AP client will connect to the AP according to SSID. MAC Address of Root AP - If you select the radio button before MAC Address of Root AP, the AP client will connect to the AP according MAC address. Enable Wireless Radio - Select or deselect this check box to allow or deny wireless stations to access the device. Note: To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device. 35 TL-WA701ND 150Mbps Wireless N Access Point User Guide 5) Bridge with AP: This mode can bridge the AP and up to 4 APs also in bridge mode to connect two or more wired LANs. Figure 4-14 Wireless Settings in Bridge with AP mode Wireless Bridge Settting Wireless Name of Remote AP - If you select the radio button before Wireless Name of Remote AP, the AP client will connect to the AP according to SSID. MAC Address of Remote AP - If you select the radio button before MAC Address of Remote AP, the AP client will connect to the AP according MAC address. Key type - This option should be chosen according to the AP's security configuration. It is recommended that the security type is the same as your AP's security type. Enter 0 to disable the update. 2) 3) • • • • • 38 TL-WA701ND 150Mbps Wireless N Access Point User Guide WPA/WPA2-Enterprise - Select WPA/WPA2 based on Radius Server. • 1) Version - You can select one of following versions. Automatic - Select WPA or WPA2 automatically based on the wireless station's capability and request. Group Key Update Period - Specify the group key update interval in seconds. Enter 0 to disable the update. 2) 3) • • • • • WEP - Select 802. 11 WEP security. • 1) Type - You can select one of following types. Automatic - Select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. ASCII format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. WEP Key - Select which of the four keys will be used and enter the matching WEP key information for your network in the selected key radio button. These values must be identical on all wireless stations in your network. Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit. ) for encryption. For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 5 ASCII characters. [. . . ] If you still cannot access the configuration page, please restore your Access Point’s factory default settings and reconfigure your Access Point following the instructions of this QIG. Please feel free to contact our Technical Support if the problem persists. Note: While the reconfiguration is done, you need to change the IP address settings as below. Then, with the correct hardware connection, you can surf the Internet successfully. 72 TL-WA701ND 150Mbps Wireless N Access Point User Guide Appendix D: Specifications General Standards and Protocols Safety & Emission Ports IEEE 802. 3, 802. 3u, 802. 11n, 802. 11b and 802. 11g, TCP/IP, DHCP FCC、CE One 10/100M Auto-Negotiation LAN RJ45 port, supporting passive PoE 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) Cabling Type Wireless Frequency Band 2. 4~2. 4835GHz 11n：up to 150Mbps（Automatic） Radio Data Rate 11g：54/48/36/24/18/12/9/6M（Automatic） 11b：11/5. 5/2/1M（Automatic） Frequency Expansion Modulation Security DSSS(Direct Sequence Spread Spectrum) DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM WEP/WPA/WPA2/WPA2-PSK/WPA-PSK 130M: -68dBm@10% PER 108M: -68dBm@10% PER; 54M: -68dBm@10% PER 11M: -85dBm@8% PER; 6M: -88dBm@10% PER 1M: -90dBm@8% PER 5dBi Sensitivity @PER Antenna Gain Physical and Environment Working Temperature Working Humidity Storage Temperature Storage Humidity 0℃~40℃ (32℉~104℉) 10% ~ 90% RH, Non-condensing -40℃~70℃(-40℉~158℉) 5% ~ 90% RH, Non-condensing 73 TL-WA701ND 150Mbps Wireless N Access Point User Guide Appendix E: Glossary 802. 11b - The 802. 11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2. 4GHz, and WEP encryption for security. [. . . ]