User manual UNIDEN EX945
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual UNIDEN EX945. We hope that this UNIDEN EX945 user guide will be useful to you.
Manual abstract: user guide UNIDEN EX945
Detailed instructions for use are in the User's Guide.
[. . . ] This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. [. . . ] Wrap the power cord around the strain relief notch on the bottom of the Base Unit.
T Place the power cord so that it does not create a trip hazard, or
Adapter Safety Feature
The AC adapter furnished with this phone may be equipped with a polarized line plug -- a plug having one blade wider than the other. If you are unable to insert the plug fully into the outlet, try reversing the plug. about replacing the outlet.
where it could become chafed and create a fire or other electrical hazards.
T If you cannot plug the AC adapter into the outlet, contact someone
EX 905/925
9
Desk or Tabletop Installation
1. Place the Base on a desk or tabletop.
T In desk or table top installation,
the Handset is designed to stand only vertically in the Base Unit. Plug the AC Adapter cord into the 9 VDC input jack on the Base Unit.
3. Place the AC Adapter cord around the strain relief notch.
10
EX 905/925
4. Plug one end of the long telephone cord into the TEL LINE jack on the Base Unit.
5. Plug the other end of the cord into the telephone jack on the wall.
6. Plug the AC Adapter into a standard 120 VAC wall outlet.
T Do not use an outlet
controlled by a wall switch.
Use only the Uniden AC Adapter supplied with this phone.
EX 905/925
11
Wall Installation
Standard Wall Plate Mounting These phones are designed to be mounted on a standard AT&T or GTE wall plate. Then, put the AC Adapter cord inside the molded channel.
12
EX 905/925
3. Plug one end of the short telephone cord into the TEL LINE jack on the Base Unit. The Handset beeps and the talk · batt low LED flashes once every 3 seconds. Return the Handset to the Base Unit for charging.
T Allow 15 to 20 hours without any interruption for the Handset to
fully recharge.
Setting the Pulse/Tone Switch
Be sure the PULSE/TONE switch is in the TONE position.
T
Most phone systems are Tone dialing. Check with your local phone company if you are not sure whether your system is Tone or Pulse dialing
20
EX 905/925
Adjusting Ringer Controls
Ringer Tone and Volume While the phone is not in use, press ringer. The phone has two ringer tones with two volume levels one soft and one loud. Each time you press ringer, the ringer/volume changes.
Receiver volume While you are on a call, press volume. Each time you press volume, the receiver volume changes.
EX 905/925
21
Automatic Digital Code Security
To avoid unauthorized calls on your phone, a Digital Code was added to all EX 905/925 phones. To change the Digital Code, be sure the Handset is on the Base, then: 1. While the Handset is still beeping, place it back on the Base Unit.
4. When the beeping stops, briefly remove the Handset again, and then return it to the Base Unit. The status LED will blink to indicate that the Digital Security Code is set to one of the more than 65, 000 codes.
22
EX 905/925
If the Base Unit loses power while the Handset is off the Base, the Digital Code may be erased. The status LED blinks to indicate that the Digital Security Code is set.
EX 905/925
23
Changing the Beltclip
Attach the beltclip 1. [. . . ] · Check both ends of the Base Unit telephone
line cord.
· Make sure the AC Adapter is plugged into the
Base Unit and wall outlet.
· Disconnect the AC Adapter for a few minutes,
and then reconnect it. Handset doesn't ring or receive a page.
· Nickel-Cadmium battery pack may be weak. · · · ·
Charge the battery on the Base Unit for 15 to 20 hours. Make sure the phone is not plugged into an outlet controlled by a wall switch. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE UNIDEN EX945
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual UNIDEN EX945 will begin.