User manual X10 MT10A

[. . . ] Mini Timer Owner's Manual Mini Timer MT10A Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Quick Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 How to program a timed event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Special programming buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If within 4 seconds after setting an on or off time, you press the "Once" button you will modify the program to carry out your programmed event only once and it will not repeat on the next day. Press (within 4 seconds after setting an ON or OFF time) to modify the program so that your lights (or appliances) will go on or off at a slightly different time every day (within the programmed hour). Pressing this (in the Review mode) cancels the on time or off time being displayed. In the "ON" position an internal wake up buzzer will sound at the time programmed for Module number 1 (or 5). When this sounds you can turn it off by pressing any button to obtain the "snooze" feature. This will turn the buzzer back on in 10 minutes and will do so each time you operate snooze. The alarm can be cancelled by moving the Buzzer switch to "OFF" and back to "ON" (for wake up the next morning). Pressing "Sleep" after turning a Module on will turn it off -15 minutes later. Pressing "Sleep" after turning a Module off will turn it on - 15 minutes later. Multiple presses adds multiples of 15 minutes to your on time (or off time). Used to select whether you want your Mini Timer to control Modules set to Unit Codes 1 thru 4 or 5 thru 8. You can move the selector switch back and forth to achieve instant control of 8 X10 Modules but you will only be able to set times for one group (1 to 4 OR 5 to 8). Battery Light When you first plug in the Mini Timer the display will flash. It will also flash if you have had a power outage and have not installed a 9 volt battery or the battery is dead. 1. Press the right hand "Time" rocker to advance to the correct time. If you hold the rocker down the display will advance to the correct time faster. If you overshoot, you can use the left hand rocker to go back. Controlling X10 Modules Follow the steps below to make sure you can control your Modules before you program the Mini Timer. 1. Install and set up all of your X10 Modules referring to the instructions included with them. Be sure to turn off the power at the main circuit breaker panel when installing Wall Switch Modules. 2. Set all of your Modules to the same Housecode as you set on the Mini Timer. 3. Set each Module to a Unit Code Between 1 and 4 (or between 5 and 8 if you set the Selector Switch on the Mini Timer to the 5-8 position. ). 4. Set the Mode Switch on the Mini Timer to the "RUN" position. 5. To turn on a particular Module, press the ON rocker key corresponding to the number you set on the Module you want to control. [. . . ] This is useful to suspend the wake-up function on weekends. To Cancel the wake-up alarm When the alarm sounds at the time you have set, you can cancel it in one of two ways: 1. Slide the Buzzer switch to the OFF position. Slide the switch back to "ON" if you want the alarm to wake you up the next morning. Pressing any key while the buzzer is sounding will turn the buzzer off and will automatically turn it back on in 10 minutes time. The buzzer will automatically turn off after 10 minutes if you ignore it. [. . . ]