User manual X10 VK59A

[. . . ] SoundPo ireless SoundPower TM W ir eless Speaker Driver System Speaker Driv OWNER'S MANUAL M O D E L VK59A SENDER RECEIVER ( INCLUDES VT35A S ENDER , VR32A R ECEIVER , REMOTE UR78A R E M O T E ) AND INTRODUCTION INTRODUCTION Your Wireless Audio Sender kit consists of a Sender base unit which connects to the audio out jack on any audio source, a Receiver unit with built-in speaker drivers to which you connect your own speakers, * and a remote control that lets you control the volume, balance, bass, treble, etc. The Audio Sender converts the audio signal from your CD player, stereo, PC sound card, etc. into a radio frequency (RF) signal and transmits it (even through walls) to the Audio Receiver unit. The Audio Receiver converts the signal back to its original form, amplifies the signal, and passes it to your connected speakers. [. . . ] Also, after you first press AUDIO followed by AMP (button 4) VOL+ increases volume on both channels VOL- decreases volume on both channels on the VR32A Amplifier/ Speaker Driver. CHANNEL +/- Used to navigate and adjust menu items of the device you are controlling. Also, after you first press AUDIO followed by AMP (button 4) the UP navigation button increases bass, DOWN decreases bass, RIGHT increases treble, LEFT decreases treble on the VR32A Amplifier/Speaker Driver. OK Works like your original remote. Also, after you first press AUDIO followed by AMP (button 4) CH+ adjusts balance to right channel, reduces left channel volume; CH- adjusts balance to left channel, reduces right channel volume on the VR32A. MUTE Selects menu items of the device you are controlling. Also, after you first press AUDIO followed by AMP (button 4) OK restores the default settings for balance, bass, and treble on the VR32A Amplifier/Speaker Driver. PLAY, REW, FF, STOP, PAUSE, REC PLAY FF, STOP, PAUSE, Works the same as your original remote. Also, after you first press AUDIO followed by AMP (button 4) MUTE toggles the audio output ON/OFF on the VR32A. 0-9 Work the same as on your original remote. You must press the REC button twice to begin recording. A, B, C, D Used as your original remote and to enter device codes. Used for extra functions in certain modes. 12 13 MPLIFIER/S AMPLIFIER/SPEAKER DRIVER CONTROLLING THE VR32A AMPLIFIER/SPEAKER D RIVER ABLE, TV, CABLE SETTING UP FOR TV VCR, CABLE, AND AUX , 1. Press and release mode button for the device you want to control (TV, VCR, Cable or AUX). If the device responds, setup is complete. Press and release the AUDIO button. This puts the remote into the mode to control the VR32A Wireless Amplifier/Speaker Driver. 1. Press and release the ENTER button to complete the setup. The UR78A remote can also control an MP3, DVD, and CD player in your PC when used with an additional RF receiver and software. You will need to purchase an MR26A receiver which connects to your PC's serial port. You then download the software (called Boom) from X10's Web Site (www. x10. com). You will then be able to control a DVD or CD player in your PC as well as being able to control MP3 players such as MusicMatch, RealJukeBox, WinAmp, etc. , remotely from anywhere inside or outside your home. The AUDIO button is also a PC button so to access your PC you just press AUDIO (PC) followed by button 1 (MP3) or button 2 (DVD) or button 3 (CD). When used in conjunction with the VT35A Audio Transmitter, and VR32A Audio Receiver/Speaker Driver, you will be able to listen to MP3 files stored in your PC while sitting outside having a barbecue. The above assumes that you want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc. , first follow the procedure on page 15 and try ANY CBL code from the code tables, e. g. Then follow the steps above. CODES SEARCH PROCEDURE IDENTIFYING CODES FOUND USING THE SEARCH PROCEDURE 1. Press the mode button that matches the equipment you want to identify (TV, VCR, CBL). To find the first digit, press each number button from 0 to 9 until the LED blinks. Press each number button from 0 to 9 again as above to find the second digit. When the third digit has been found, the LED goes out. Pressing AUDIO (PC) followed by 1 (MP3) or 2 (DVD) or 3 (CD) accesses your PC, when used with the optional MR26A receiver and Boom software. 16 17 H OME CONTROL CONTROL The UR78A remote can also control lights and appliances around your home when you purchase additional X10 accessories (See pages 24 and 25). CODES H OUSE C ODES AND UNIT CODES U NIT C ODES Each Module has a specific address made up of a House Code (red dial on the face of the Module) and a Unit Code (black dial on the face of the Module). UNIT CODE The Controller first sends an address and then a command on the AC power lines. [. . . ] · Reenter the code for your A/V product from the code listings on the separate sheet included. · Replace the Remote's batteries. IF YOU ARE NOT GETTING ANY SOUND AT ALL FROM THE VR32A · Check that the CHANNEL slide switch (labeled A, B, C, D) on both units is set to the same letter. · Check that both the transmitter and receiver's power supplies are plugged in. Check that the ON/OFF switch on the transmitter and receiver are ON. POOR, IF THE SOUND IS POOR, OR THERE IS INTERFERENCE · Try changing the channel on both units. [. . . ]