User manual X10 VK74A
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual X10 VK74A. We hope that this X10 VK74A user guide will be useful to you.
You may also download the following manuals related to this product:
X10 VK74A QUICK SETUP (29 ko)
Manual abstract: user guide X10 VK74A
Detailed instructions for use are in the User's Guide.
[. . . ] OWNER'S MANUAL
XM14A POWER SUPPLY
C1
CAM ERA
C2
C3
C4
P1
POSITION
P2
P3
Cente r
P4
Sweep
CAMERA (SOLD
SEPARATELY)
M
. O .
K
. A . C . . E . I. G
SCAN
Normal
Pro gra m
CR14A REMOTE
ZC15A PAN 'N TILT BASE
MODEL VK74A PAN 'N TILT CAMERA SYSTEM
INCLUDES ZC15A PAN 'N TILT BASE, XM14A ADDRESSABLE POWER SUPPLY, CR14A REMOTE (CAMERA SOLD SEPARATELY)
INTRODUCTION
The VK74A includes the ZC15A Pan `n Tilt Camera Base with XM14A remote controlled power supply, and the CR14A remote control. You attach any XCam2 wireless camera (XX11A or XX13A) or any XCam 2 Instant On Camera (XX16A or XX17A) to the Pan `n Tilt Camera Base and then you can remotely control the camera's position using a CR14A remote control. The camera sends the picture and sound to a Receiver that you connect to your TV, up to 100 ft. [. . . ] Set each power supply to a different number within one of the groups (1-4, 5-8, 9-12, or 13-16).
5. Position the Video Receiver in a convenient location such as on top of the TV and orient the antenna so that the flat side points in the direction of the room where you set up the Camera.
Point antenna towards the Receiver
IF YOUR TV IS ALREADY HOOKED UP TO A DBS RECEIVER OR OTHER A/V DEVICE, OR IF YOUR TV DOES NOT HAVE A VIDEO IN
JACK
Outdoors
Indoors
If a DBS Receiver or other A/V component is connected to the TV using A/V cables, you can connect the Video Receiver to the free LINE IN jacks on the component.
10
11
REMOTE CONTROL
The Remote lets you move the camera from left to right (Pan) and up and down (Tilt). You can store 4 positions for the camera and use the remote to "Sweep" between these positions. Install 4 AAA alkaline batteries (sold separately) in the remote's battery compartment.
"Tilts" up and down. Pressing any of these turns on that camera, and turns the other 3 off (Transceiver required). Sweeps thru the 4 stored positions for the selected camera.
Pro m gra
SINGLE CAMERA OPERATION
Press a left or right BLUE button at the top of the CR14A Remote to "Pan" the camera left or right. Press a BLUE up or down button to "Tilt" the camera up or down. Buttons P1 thru P4 are used to store 4 position settings for the camera. To store the first position for the camera, press the BLUE buttons to scan to the position you want. To store the second position for the camera, press the BLUE buttons to scan to the position you want. To store the third position for the camera, press the BLUE buttons to scan to the position you want. To store the fourth position for the camera, press the BLUE buttons to scan to the position you want. To clear all stored positions: Move the switch at the bottom to Program. Press C2 and repeat steps 2 to 7 above to store 4 positions for Camera C2. To control up to 4 Cameras, plug each one into its own Addressable Power Supply, and set each power supply to the same Housecode you set on the Transceiver and the Remote. Pressing any Camera button (C1, C2, C3, or C4) turns on that camera (1, 2, 3, or 4) and turns the others (in the group) off. Then, each press of either the or button turns on the next or previous camera in the group of 4 while turning the current camera off. You must set all cameras to the same channel as the Video Receiver VR31A, or VR36A (Channel A, B, C, D). To "Pan" or "Tilt" a camera: Press C1, C2, C3, or C4 to turn on the camera. Then press a left or right BLUE button at the top to "Pan" the camera left or right. Press a BLUE up or down button to "Tilt" the camera up or down. Press C3 and repeat steps 2 to 7 above to store 4 positions for Camera C3. [. . . ] If the camera gradually drifts off the positions you have programmed: This can happen if the positions you programmed do not cause the camera to pass through center. If you notice the positions that you programmed for sweep starting to drift out of position after a while, just press the Center button on the remote to reset the positions to where you programmed them. Or you can make the camera periodically center automatically as follows: Within 3 seconds after you plug the camera's power supply in, press P1, P2, P3, or P4 on the remote. Pressing P1 within 3 seconds after you power up forces the camera to recenter every 32 sweeps through the positions you have programmed.
Pressing P2 within 3 seconds after you power up forces the camera to recenter every 64 sweeps through the positions you have programmed. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE X10 VK74A
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual X10 VK74A will begin.