User manual YAESU FT-2800M

[. . . ] FM TRANSCEIVER FT-2800M OPERATING MANUAL PWR MHz REV LOW D/MR VERTEX STANDARD CO. , LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U. S. A. 52nd Terrace, Suite 201, Miami, FL 33166, U. S. A. YAESU EUROPE B. V. P. O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K. VERTEX STANDARD HK LTD. Unit 5, 20/F. , Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the [MHz(SET)] key momentarily, then rotate the DIAL knob one click counterclockwise to select Menu "26 SQ DCS. " 7. Press the [MHz(SET)] key momentarily to enable the adjustment of the DCS Code. Rotate the DIAL knob to select the desired DCS Code (a three-digit number). When you have made your selections, press and hold in the [MHz(SET)] key for one second to save the new setting and exit to normal operation. FT-2800M OPERATING MANUAL 27 ADVANCED OPERATION DTMF AUTODIALER OPERATION Nine DTMF Autodialer memories are available on the FT-2800M. These DTMF Autodialer memories can store up to 16 digits of a telephone number for repeater autopatch or other use. Press and hold in the [MHz(SET)] key for one second, then rotate the DIAL knob to select "10 DT MEM. " 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the DTMF Autodialer memory channel number into which you wish store a telephone number ("DTMF-1" to "DTMF-9"). Press the [D/MR(MW)] key momentarily, then rotate the DIAL knob to select the first digit of the telephone number you wish to store. When you have selected the correct digit, press the [REV(DW)] key momentarily. Now, rotate the DIAL knob to select the second of 16 available numbers in the current DTMF Autodialer memory register. If you a mistake, press the microphone's [DWN] key to move back to the first digit, then re-enter the correct number. If you wish to store another DTMF string, repeat steps 2 through 6 above. Press and hold in the [MHz(SET)] key for one second to save the new setting and exit to normal operation. To transmit the memorized telephone number, use the following procedure: 1. Press and hold in the [MHz(SET)] key for one second, then rotate the DIAL knob to select "08 DTMF. " 2. Press the [MHz(SET)] key, then rotate the DIAL knob to set the DTMF Autodialer memory function to the "ON" position (the " " icon will appear). Press and hold in the [MHz(SET)] key for one second to save the new setting and exit to normal operation. In the Autodialer mode, which you just engaged, first press the PTT switch, then press the microphone's numeric key ([1] through [9]) corresponding to the DTMF memory string you wish to send. Once the string begins, you may release the PTT switch, as the transmitter will be held "on the air" until the DTMF string is completed. To disable the Autodialer function mode, select "OFF" in step 2 above. 28 FT-2800M OPERATING MANUAL ADVANCED OPERATION DTMF AUTODIALER OPERATION The speed at which the DTMF digits are sent can be changed. Two speed levels are available: Low (10 digits per second) and High (20 digits per second: default). Press and hold in the [MHz(SET)] key for one second, then rotate the DIAL knob to select "11 DT SPD. " 2. [. . . ] HOME: Pressing the [REV(DW)] key instantly recalls a favorite "Home" channel. 52 FT-2800M OPERATING MANUAL "SET" (MENU) MODE MENU SELECTION DETAILS 20 RF SQL Function: Adjusts the RF Squelch threshold level. Available Values: 1 - 10, or OFF Default: OFF 21 RPTR Function: Sets the Repeater Shift direction. Available Values: ­RPTR/+RPTR/SIMP Default: SIMP 22 RVRT Function: Enables/disables the "Priority Channel Revert" feature. Available Values: ON/OFF Default: OFF 23 SCAN Function: Selects the Scan Resume mode. [. . . ]