User manual YAMAHA MAGICSTOMP
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual YAMAHA MAGICSTOMP. We hope that this YAMAHA MAGICSTOMP user guide will be useful to you.
You may also download the following manuals related to this product:
YAMAHA MAGICSTOMP (682 ko)
YAMAHA MAGICSTOMP (943 ko)
YAMAHA MAGICSTOMP (1 ko)
YAMAHA MAGICSTOMP 2 (68 ko)
YAMAHA MAGICSTOMP 3 (149 ko)
YAMAHA MAGICSTOMP 4 (238 ko)
Manual abstract: user guide YAMAHA MAGICSTOMP
Detailed instructions for use are in the User's Guide.
[. . . ] This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Failure to follow instructions could void your FCC authorization to use this product in the USA. [. . . ] If you feel output is low when the switch is set to the LOW position, change the setting to HIGH. · When using patches with stereo output, we recommend connecting the MAGICSTOMP's output jacks to a stereo device. · When connecting to a monaural device, use the OUTPUT L/MONO jack. · When connecting the power adaptor to the MAGICSTOMP's AC IN jack, you can wrap the power adaptor cord around the cord hook as shown in the illustration below (this helps keeping the plug from being accidentally pulled out).
CAUTION
· Don't let the cord bend sharply or kink when wrapping the cord around the hook. An excessive bend can cut the cord or start a fire.
AC IN jack
Cord hook
Power adaptor cord
10
Connections Using the MAGICSTOMP with a guitar or other instrument
Connecting to a guitar amplifier (monaural)
INPUT
Connecting to guitar amplifiers (stereo)
INPUT INPUT
Connecting to a recording device, etc.
INPUT
INPUT
L/MONO
L/MONO R
L/MONO
R
OUTPUT L/MONO
R
* The AC adaptor's shape will vary according to the country to which the device is shipped. Power Adaptor (supplied) AC-10 Electric Outlet
AC IN
INPUT
Guitar, or other instrument
U99¤MAGICSTOMP óGAINfiMSTRáTONE
MAGICSTOMP
Using the MAGICSTOMP in an effect loop
Power Adaptor (supplied) AC-10 Electric Outlet * The AC adaptor's shape will vary according to the country to which the device is shipped.
OUTPUT L/MONO AC IN R INPUT
EFFECT SEND
EFFECT RETURN L R
U99¤MAGICSTOMP óGAINfiMSTRáTONE
MAGICSTOMP
Mixer, etc.
11
Using the MAGICSTOMP
The MAGICSTOMP comes loaded with a variety of effect patches (programmed effects). First, give some of the presets a try and see what's available.
Turn on the amplifier and play
You'll hear the currently selected patch. Use the MAGICSTOMP's VOLUME knob to adjust the MAGICSTOMP's output volume.
Patch No. Patch Name
U99¤MAGICSTOMP0 óGAINfiMSTRáTONE Try out some of the other patches
The MAGICSTOMP has a total of 198 patches. 99 of those are User Patches (U01 U99) to which you can save (overwrite) data of patches that you have created. The other 99 are Preset Patches (P01 P99) which can not be overwritten with new data. You can however, edit the Preset Patches and save them in the User Patch section.
* When shipped from the factory, the MAGICSTOMP's User Patch section contains the same data as found in the Preset Patches.
Two ways to select patches
When the MAGICSTOMP is shipped from the factory, its [UP/DOWN MODE] is already set for the patch selection mode. In this mode, just press the + switch to move to the next greater patch number, and press the switch to move to the next lesser patch number. Hold either switch down and the patch numbers will quickly cycle up or down in order. In this mode, the ON/OFF switch is used to switch the patch (effect) on or off.
Pressing the switch decreases the patch number by 1
U01 U98 U99 P01 P97 P98 P99
U01¤DIST óBAL0fiSTERáVOL
Pressing the + switch increases the patch number by 1
P99 P02 P01 U99 U04 U03 U02
Effect ON
Effect OFF
U01¤DIST óGAINfiMSTRáTONE
U01¤DIST ó EFFECT OFF
12
Using the MAGICSTOMP
The other way to select patches is with the [Performance Mode]. In this mode, the , +, and ON/OFF switches are used to turn three adjacent patches ON and OFF.
q To enter the Performance Mode, press and hold any two switches (from , +, and
ON/OFF).
"PERFORMANCE MODE" appears in the display to inform you that the MAGICSTOMP is now in the Performance Mode.
w Press and hold the or + switch to change the patch set.
switch: U01/02/03P97/98/99P94/95/96. . . + switch: U01/02/03U04/05/06U07/08/09. . .
* Patch sets (three adjacent patches make a patch set) have been predetermined. * When the MAGICSTOMP switches to the Performance Mode, the patch set containing the patch number selected with the Up/Down Mode is selected.
e To return to the UP/DOWN Mode, press and hold any two switches (from , +,
and ON/OFF).
"UP/DOWN MODE" appears in the display to inform you that the MAGICSTOMP is now in the Up/Down Mode.
Example) Switching from the Up/Down Mode (patch U06 is selected) to the Performance Mode.
When in the Performance Mode, the lamp of the currently selected patch lights (U05 is selected in the illustration below). Patch U04 ON/OFF switch Patch U06 ON/OFF switch
U06¤AG0TUBE100 óBALVfiSTERáVOL
Up/Down Mode
Press and hold any two of the three switches
Press and hold the switch. U01/02/03 P97/98/99 P94/95/96 P91/92/93 : :
Patch U05 ON/OFF switch
Press and hold the + switch. U07/08/09 U10/11/12 U13/14/15 U16/17/18 : :
U06¤AG0TUBE100 PERFORMANCE0MODE
U06¤AG0TUBE100 >ãBAL0ÄSTERÄVOL
Performance Mode
When all three patches are switched OFF, the display appears as follows (all lamps are off).
U05¤AG0DYNAMIC2 >0OFF0(U04:05:06)
13
Create your own sound
Use the knobs to adjust the effect
The three knobs located below the display let you adjust different characteristics of the effect. The parameters that these knobs adjust, differ according to the selected patch. [. . . ] Is the volume control on the instrument connected to the INPUT jack turned up? Is the effect's output level set to "0"?
· Sound level is low
Switch the input level to the "HIGH" position. ( P. 10)
· Effect is not active
Is the effect's output level set to "0"? Is the effect switched OFF (all lamps are off)?
· Can not change to another patch
Check the display. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE YAMAHA MAGICSTOMP
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual YAMAHA MAGICSTOMP will begin.