User manual YAMAHA RAV120
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual YAMAHA RAV120. We hope that this YAMAHA RAV120 user guide will be useful to you.
Manual abstract: user guide YAMAHA RAV120
Detailed instructions for use are in the User's Guide.
[. . . ] For other units, use the original remote control supplied with the product.
HOW THE REMOTE CONTROL WORKS
The remote control can learn the functions of other remote controls, so one remote will control your home theater audio and video components. The shaded areas shown in the illustration on the left have learning capabilities, using data stored in any of three different memories: · A is preprogrammed for Yamaha audio components · B for video components · C for additional components, unique functions, or non-Yamaha audio components Unshaded buttons will become control buttons, once the appropriate functions have been programmed into the remote control.
YAMAHA REMOTE LEARNING KEYS
For Learning For Clearing
T RANSMI T / L E A RN CLEAR LEARN MA CRO
REC/ PAUSE
A /B TAPE
CD
Learning Controls For Tape Decks or VCRs
STOP
TUNER
A
DIR
B D ISC
VC R
Transmit/ Learn LED Use the following sections to set up the remote control and to program most of the standard VCR and TV functions. Once you have programmed the remote control, you can close the lid to conveniently access and control most of the functions of your audio and video equipment. [. . . ] Repeat steps 1 through 8 for any function that does not respond.
Remote Control Guide ·
LOCATIONS OF TV LEARNING BUTTONS
T RANSMI T LE ARN CLEAR LEARN MA CRO
HOW TO PROGRAM TV REMOTE FUNCTIONS
To program basic functions of the TV remote, we suggest you learn functions into all the shaded buttons shown in the illustration on the left: 1. Aim the TV remote control transmitter (usually located at the top) at the top of the Yamaha remote.
REC PAUSE
AB TAPE
CD
TUNER
2. Slide MEMORY Switch To B
A STOP
DIR
B D ISC
VC R
D V D LD
Remote With Lid Open TV Remote Control
REC PAUSE
CLEAR
T V D BS
VOLUME UP VOLUME DOWN CHANNEL KEYPAD (0~9)
A DIR B
LEARN
2~4"
T RANSMI T LE ARN
MA CRO
AB
CHANNEL UP
PRO LOGIC ENHANCED CONCERT VIDEO
1
MONO MOVIE
2
S TAD IUM
3
DI SC O
AUX V--
TUNER
TAPE
VC R
CD
4
R O CK
5
H A LL
6
PHO N O
7
8
9
TEST
EFF ECT
0
TIME LE V EL
TV INPUT
DELAY CENTER REAR SWFR
3.
CHANNEL DOWN
SLEEP
On the Yamaha remote, use a paper clip or mechanical pencil to press LEARN. NOTE: If there is no operation for about 30 seconds after a button is pressed, the TRANSMIT/LEARN LED will flash repeatedly. If this occurs, restart from step 3.
2CH/6CH
SY S T E M P O W ER TV
MAS T ER VO LUM E
TV POWER 4.
OFF
VCR
On the Yamaha remote, press and release the button to which you want to assign the function. On the TV remote, press and release the button for the corresponding function. The TRANSMIT/LEARN red LED on the Yamaha remote control will flash slowly after the function is learned. NOTE: If the TRANSMIT/LEARN red LED on the Yamaha remote flashes rapidly, the function has not been learned. Repeat steps 5 and 6 to program the function.
5.
R EMO T E C ONT R O L T R ANSMIT T ER
Remote With Lid Open
6.
7. 9.
Continue programming until you have learned functions into all of the shaded buttons. Repeat steps 1 through 8 for any function that does not respond.
Remote Control Guide ·
BASIC OPERATION CONTROLS
TRANSMI T
USING FACTORY-PRESET OPERATIONS
In addition to the programmable VCR and TV functions, the Yamaha remote control will also perform several factory-preset operations without additional programming (see the illustration on the left): 1. Press the SYSTEM POWER button to power up your Yamaha receiver, VCR, and TV. NOTE: Since power ON and OFF are controlled by the same button on most audio and video components, the (SYSTEM POWER) OFF button may not turn off your VCR and TV automatically (see "Creating A Macro" on the next page). Press the VCR button to set the input on the receiver to VCR and put the VCR into PLAY mode. (Make sure there is a videocassette in the machine. ) NOTE: You may have to adjust the INPUT on your TV to see the VCR's video signal. If you have programmed the TV inputs into the Yamaha remote's TEST button, simply press it (one or more times) until you see tape playback. [. . . ] Press the OFF button to clear the original factory macro and assign the new sequence of functions (i. e. , steps 5, 6, and 7) to this button. Slide the Macro switch (on the side) to QUICK.
CD
TUNER
A STOP
DIR
B D ISC
VC R
D V D / LD
T V/ D BS
PRES E T
PRO LOGIC
ENHANCED
CONCERT VIDEO
1
MONO MOVIE
2
S TAD IUM
3
DI SC O
VAU
4. 7.
4
R O CK
5
H A LL
6
PHO N O
7
8
9
TE S T
EFF ECT
0
TIME / LE V EL
DELAY CENTER REAR SWFR
8. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE YAMAHA RAV120
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual YAMAHA RAV120 will begin.