User manual ZANUSSI ADVANTAGE500

[. . . ] WASHING MACHINE PRALKA AUTOMATYCZNA AUTOMATA MOSÓGÉP AUTOMATICKÉ PRACKY AUTOMATICKÁ PRÁCKA INSTRUCTION BOOKLET INSTRUKCJA OBSLUGI HASZNÁLATI ÚTMUTATÓ NÁVOD K OBSLUZE NÁVOD NA OBSLUHU 35. 292. 618/0 CONTENTS Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking and installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transit security bars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] s Do not overload the appliance, see the relevant WASHING PROGRAM section. s Before opening the door look through the "window" to check if the water has been drained. s Leave the porthole slightly ajar between washes to preserve the door seal. s Serious damage can occur to the product and to property if this has not been adhered to. s The washing machine must be unplugged when removing the interior transit bolts. Do not plug the appliance before finishing the removal of the transit bolts and the fixing of the caps in the holes where the security bolts were. s If the appliance is to stand on a carpeted floor make sure that there is space between the carpet and the supporting feet of the appliance for the air to circulate freely around . s Care must be taken to ensure that the appliance does not stand on the electrical supply cable. 3 ENGLISH UNPACKING AND INSTALLATION TRANSIT SECURITY BARS Before starting the machine up, the transport security bars must be removed as follows: You are advised to keep all the transport security bars in case the appliance has to be transported again. Unscrew and remove the three rear screws by means of a key. HYDRAULIC CONNECTION There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3/4 gas for the water supply, a sink, a wash basin or a drainage system in the wall. If not, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Have the permanent drainage system in the wall checked by a plumber. Place the enclosed rubber joint, delivered in a plastic bag together with the appliance (A), at the very end of the inlet hose and carefully screw the pipe to the tap taking care not to damage the screwdrive and fix the nut well on to the end in order to avoid leaking. If necessary turn the hose adequately by unscrewing the nut at the rear of the appliance. 2. Lean the appliance back on the rear and fit one of the polystyrene angles between the appliance and the floor. Carefully remove the plastic bags on the right and the left, pulling them to the centre of the appliance. Now tighten the nut anew to avoid leaks. (Open the tap and asure that it does not leak and close it again. ) Place the discharging hose in a washbasin or sink with the aid of the bent piece delivered separately. The bent piece has to be entered into the tube's mouth in order to assure the support. Aforesaid piece allows the hose to be fixed to the wall by means of an opening on the upper part and that way the hose does not move and its falling is avoided. 4. Place the machine in an upright position and remove the three plastic bolts. 5. TEMPERATURE SELECTOR This control allows you to select the temperature of the washing cycle in accordance with the kind of clothes to be washed. Turn the control until the required temperature coincides with the marker. «Prewash» symbol shows the compartment for the prewash detergent. «Wash» symbol shows the compartment for the washing detergent. «smooth» symbol shows the compartment for the smoothing additives. On the program table you will find the most appropriate temperature for each kind of washing. [. . . ] If the laundry is not very soiled this will be enough and it is energy saving. If you want to wash whites without temperature, you must choose the program B. Coloured fabrics are advised to be washed at 40°C although they would stand 60°C. When washing together dark and light coloured fabrics the temperature should not exceed 40°C. [. . . ]