User manual ZANUSSI S400X

[. . . ] Tips and instructions for the economical and environmentally sound use of the appliance are marked with this symbol. These instructions contain informations on how to rectify faults yourself. " Should you require further assistance, please contact your local Service Force Centre. 2 Content For the user Dear Customer !Safety information Disposal of packaging material Hints of disposal Before the first use Cleaning for the first time Description of the hob Digital indicators Special features of the appliance Operating instructions General information TOUCH--CONTROL--sensorfields Switchin on the appliance Switching off the appliance Cooking zone selection Setting selection Cooking zone switch--off Residual heat indicator Child safety device Safety cut--off after time Safety cut--off due to a spillage Application, charts, tips Cooking and frying utensils General hints Energyconsumption Chart: boiling and frying Cleaning and care Ceramic glass surface Light soilage Stubborn soilage Special soilage Sugar Dark spots and decor damages Scratches in the ceramic glass surface The hob frame What to do . . . [. . . ] Care will have to be taken until there is no longer a risk of burning. 9 Child-safety device Acitivating the child-safety device The child--safety device prevents the cooking zones being switched on accidentally. The child--safety device can only be activated when the hob is switched on. Immediately after (within 10 seconds) touch the and controls at the same time for about two seconds and then release. The child--safety device is now activated. D 3 Use of the cooking area with the child-safety device activated D D 1. Within 10 seconds touch the and controls at the same time for about two seconds. The child--safety device remains deactivated until you next switch off the apliance. All cooking zones and settings can be used as normal. D Deacitivating the child-safety device The child--safety device can only be deactivated when the hob is switched off. Touch and controls at the same time for about 2 seconds and the release. 10 3 D Safety cut off after a time If a cooking zone is not switched off or if a setting is not varied after a defined time, the corresponding cooking zone will switch off automatically. D The cooking zones switch off as follows: S setting 1 ­ 2 after 6 hours S setting 3 ­ 4 after 5 hours S setting 5 after 4 hours S setting 6 ­ 9 after 1. 5 hours after To re--set the cooking zones, if required, the appliance must be switched back on using the main switch ON/OFF. Safety cut off due to a spillage Liquids that boil over and spill onto the surface will cause the cooking zones to switch off. The front right and rear cooking zones can still be operated during this time. . . . if the display Check, whether D lights up? D the touch controls are entirely or partly covered or contaminated by liquid or by a wet cloth. if the whole indicator section for residual heat, except , will fail all of a sudden?was accidentally Check, whether D D D D the ON/OFF touch control touched. D D the touch controls are entirely or partly covered by liquid or by a wet cloth. the cooking zone automatically switches back to setting 7 during cooking?D Because the temperature is too high, the electronic control thermal cutoff has triggered an automatic reduction of the cooking setting. You can increase the cooking setting again, after the cookuing zone has cooled down. If you try to increase the setting again and the display flashes, this means that it is not yet possible to carry out the desired increase, because the appliance is still too hot. . . . if the displays suddenly go out? Check, whether D D D the fuse has failed. if after cooking zone switch--off the display will not show D Check, whether the cooking zone has only been in operation for a short while, and is therefore not hot enough. If after carrying out the above checks your appliance is still faulty, disconnect from the mains supply and contact your local Service Force Centre. [. . . ] Then fasten the catch springs with screws in the cut--out at the marked position. With natural, artificial stone, or ceramic plates the springs can be glued in with special adhesive (synthetic resin, two--component adhesive, etc. ) The cooking area is entered from the top into the cut--out section, centered and firmly pressed on until the springs will catch. Check the seal in the supporting frame for perfect seating and gapless support. Please do not apply further silicone sealing matter as this will complicate the removal of the hob if servicing is necessary. R5 D D D D D D 1 2 sealing frame ceramic glass plate worktop snap--in clamp 20 Electrical connections Before connecting the appliance, check that the voltage quoted on the rating plate - that is, the nominal voltage of the appliance - corresponds to the available mains voltage. [. . . ]