User manual ZANUSSI TC180W

[. . . ] Cabinet damage, which is not covered by guarantee, could result if this recommendation is not followed. s The power cable must be plugged into an earthed should be dried in large commercial machines because of their bulk, check with the manufacturer of the item if it is suitable for drying in a domestic machine, even if the dry weight of the item is within the limit advised. s Laundry which has been in contact with chemicals such socket, which must be easily accessible. Permanent installation must only be carried out by an authorized electrician. s Make sure that the power cable is not nipped or other- as dry cleaning fluid and similar, should not be dried in the machine, since volatile chemicals can be a fire risk. s The following items/materials should not be dried in wise damaged when moving the machine in connection with installation or cleaning etc. s The ventilation opening at the bottom of the door should not be obstructed if the dryer is on a carpeted floor. s The adjustable feet must not be removed, these ensure that the underside of the dryer is ventilated. s Servicing and repairs must be carried out by a trained service technician. Only use genuine spare parts available from your local Service Force Centre. Never try to repair the machine yourself. the machine either: ­ Pillows, cushions, down-filled items etc. [. . . ] Make sure that you put the fluff filter back correctly after cleaning, before closing the coarse filter. A B Never start the dryer unless the fluff filter is clean and correctly in place, or if the fluff filter is damaged (this could cause overheating). C The condenser As in all types of tumble dryer, the air circulated through the dryer picks up fluff. As a result, some fluff will accumulate in the condenser, so it needs to be cleaned occasionally. Grasp the recesses at the top of the condenser with your fingers and use your thumbs to press against the door (Fig. The condenser will come free, allowing you to lift it outwards/upwards. Turn it upside down and clean it on both sides, using a vacuum cleaner. Lay the condenser flat and fill it with water through the filter opening. Now leave the condenser to soak in water for about 5 minutes, then shower both sides with hot water. Make sure that its base is lined up in the slots in the condenser cavity inside the dryer door. Press the condenser carefully into place until you feel and hear a gentle "snap". Put back the fluff filter and close the coarse filter. D E F G -8- Emptying the water tank A warning light on the control panel will come on when it is time to empty the water tank. If it is operating when this happens, the dryer will stop automatically until the tank is emptied. It is a good idea to get into the habit of emptying the tank either before or after each load. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. Fault The machine will not start. Check s Is the door closed properly?s Is the water tank full? The load is not drying properly, or is taking long time to dry. s Was the time set not long enough?s Is the load too large? Cotton max 3, 4 kg Synthetics max 1, 5 kg s Is the fluff filter clogged? s Is the condenser clogged?s Have you been using the "Synthetics" setting (on the timer) (lower drying temperature)? s Is the temperature in the room too high? Must not exceed +35° C. The area around the dryer is hot. s Is the room too small?(Improve the room ventilation, open a door or window or choose another site for the dryer). Repairs carried out by unauthorised or inexperienced persons can cause injury or serious malfunctioning. ­ ­ ­ This appliance complies with the following E. E. C. amendment 92/31/EEC) ­ directive on electromagnetic compatibility. - 11 - Service Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning: 08705 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk Before calling out an engineer, please ensure you have read the details under the heading "In the event of a fault". When you contact the Service Force Centre you will need to give the following details: 1. The model and serial number of the appliance (found on the rating plate) 5. [. . . ] If the adjacent cupboards are more than 370 mm deep, don't forget to leave a space at least 30 mm wide on the left of the dryer so that the door can open wide enough. There should be a clear space at least 200 mm high between the top of the dryer and the ceiling or any cupboard above the dryer, to ensure adequate ventilation at the top. 3 - 17 - Power supply The dryer is supplied with a lead and electrical plug for connection to a 230 V, 13 A earthed wall socket. Before any work is carried out on the dryer, it must be isolated from the electric mains supply, for example by removing the plug from the wall socket. Permanent electrical installation must be carried out by an authorised electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. [. . . ]