User manual ZANUSSI TCE7124

[. . . ] Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Always insist on genuine spare parts. Child safety Use · This appliance is designed for domestic use only. If the machine is used for any other purposes or is not used correctly, the manufacturer accepts no responsibility for any damage that might occur. · Clothes which are dripping wet should not be placed in the dryer. [. . . ] Read carefully the instructions supplied with the kit before installing the dryer. Door reversal To make it easier to load or unload the laundry the door can be reversed. Please contact the nearest Service Centre. 5 ENGLISH Connecting a drain hose If there is a sink or drain near the appliance, the condensed water can be discharged directly through a hose that is available on the market. In order to connect the hose to the appliance proceed as follows: · · · · Remove the clamp (A) Pull out the plug (B) Insert the drain hose (C) Fasten the hose (C) to the appliance using the clamp (A). If the appliance is stacked on the washing machine, the condensed water can be discharged through the hose as shown in figure, but take into account that the hose (C) must be pointed downwards. 6 Use The control panel ENGLISH 6 Start button Press this button for about 2 seconds to start the dryer after having selected the programme. If the door of the appliance or the small door at the bottom is opened while the programme is running, this button must be pressed again after closing the door in order to restart the programme from the point at which it was interrupted. This button must be depressed also after a power failure and after having re-inserted the water reservoir, if it has been emptied in the middle of a programme. In both cases light or (depending on the phase in progress) flashes to remind you that the start button needs to be pressed again. 1 Programme guide This will help you to select the correct programme for drying. 2 Mains-ON light Comes on when the appliance is switched on (ON/OFF button pressed down) and goes out when this button is released. 3 ON/OFF button This button is used to switch the dryer on. At the end of the programme, release this button by pressing it again to switch the dryer off. 4 Low temperature button Pressing this button allows drying to be performed at a lower temperature, for delicate items. If the button is not pressed, drying is performed at full power (2000 W). 7 Programme phase indicator lights These lights indicate the various phases of the programme as they are being performed. "Drying" light This light indicates that the appliance is in the drying phase. "Cooling" light This light indicates that the appliance is in the cooling phase. At the end of drying, there is a 10 minute cooling phase to cool the laundry. If light or is flashing, this means that the Start button needs to be pressed again for the programme to resume. 5 Buzzer OFF button A buzzer sounds by depressing the pushbuttons, during the anti-creasing phase, at the end of programme and when the water reservoir is full. Press this button when selecting the programme if you wish to switch the buzzer off during the anticreasing phase. to remove a persistent odour of moth-balls). Load It is often difficult to estimate the weight of items to be dried. We therefore recommend that you adopt the following guidelines: · cotton, linen: drum full but not too tightly packed; · synthetics: drum no more than half full; · delicate fabrics: drum no more than one third full. 9 ENGLISH Operating sequence Before using your tumble dryer for the first time, we recommend to place a few damp cloths inside the appliance and dry for 30 minutes. There may be dust inside a brand new tumble dryer. Turn the programme selector dial to "0"; lights and go out. Release the ON/OFF button (the mains-ON light goes out) and immediately remove the laundry. After each use · Clean the filters (see page 12). If the drying programme has to be stopped before it reaches the end, we recommend that you turn the programme selector dial to position (cooling) and wait until the end of this phase before removing the laundry. This will avoid a build-up of heat inside the appliance. To do this first turn the dial to "0" and then to and depress Start button . Please check the laundry does not get caught between the door and filter. : the mains-ON light To change a programme which is running, first cancel it by turning the programme selector dial to "0". If required, press the low temperature button and/or the buzzer OFF button . Press the Start button for 2 seconds: light comes on and drying starts. [. . . ] The reservoir must be emptied after each drying cycle to ensure efficient operation when the machine is next used. If this is not done a safety device trips: pilot light on the control panel comes on and the programme stops, leaving the laundry damp. Proceed as follows: · Open the small door at the lower part of the cabinet · Turn the yellow stop upwards · Pull out the reservoir · Open the small cover and let water flow down · Close the small cover and re-insert correctly the reservoir · Push it until it clicks and turn the yellow stop downwards to lock firmly it · Close the small door and press the START/PAUSE button again to allow the programme to continue. P1162 Cleaning the drum When your laundry does not reach the desired degree of dryness, in other words, when it turns out either too dry or too damp, we advise you to clean the inside of the drum with a cloth soaked with vinegar. This will eliminate the slight patina that has formed in the drum (due to residues of detergent and softeners used in the washing, and to the lime contained in the water), which prevents the probes from detecting the correct degree of dryness. P1202 13 ENGLISH Something not working? Before contacting your local Service Centre, please make the following checks: Problem · The dryer does not work: Possible cause · The door(s) is(have) open. [. . . ]