User manual ZANUSSI ZGL643IX

[. . . ] Should you connect any electrical tool to a plug near this cooking appliance, ensure that electric cables are not in contact with it and keep them far enough from the heated parts of this appliance. If the appliance is out of order, disconnect it from the electric supply. Child Safety This appliance has been designed to be operated by adults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or play near or with the appliance. This appliance is not intended for use by children or other persons whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction by a responsible person to ensure that they can use the appliance safely. Environmental Information After installation, please dispose of the packaging with due regard to safety and the environment. [. . . ] 1 A - Burner cap B - Burner crown C - Ignition candle D - Thermocouple Models with automatic ignition Push in the relevant knob and turn it anticlockwise to "maximum position". After lighting the flame, keep the knob pushed down for about 5 seconds. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted (ZGL 646 IT - ZXL 636) . If you cannot light the flame even after several attempts, check the "cap" (Fig. Always turn the flame down or put it out before taking the pans off the burner. . Fig. 2 FO 0204 3 Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel. It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if over-heated. 160 mm. Big (rapid) Medium (semirapid) Small (auxiliary) Use of electric plate (ZXL 636) To switch on the plates, turn the relevant knob to the required position. The plates are regulated by a 7 position switch: Position 0: off Position 1: minimum disbursement of heat Position 6: maximum disbursement of heat The pilot light signals the connection of the electric plate. It is important to note that the plate may smoke a little and produce a slightly unpleasant odour when used for the first time. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOK OR THE REGULATION IN FORCE BE IGNORED. Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Screw the parts without forcing, adjust the connection in the required direction and tighten everything. IMPORTANT - When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Use some soapy water, never a flame. A) Ramp with ending nut B) Seal C) Adjustable connection FO 0264 Fig. 4 6 Electrical Connection The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. [. . . ] To install the hob, proceed as follows: 1) Place the sealing gasket (supplied with the hob) on the edges of the cut out: place it exactly on the front and rear edge, taking care that the sealings meet without overlapping; 2) Fix the hob with the relevant screws (Fig. The traction of the screws is able to trace the sealing, any excess of which can be easily removed. The edge of the hob forms a double labyrinth seal which provides a total guarantee against infiltration of liquids. a Fig. 10 FO 0199 a) Sealing gasket 9 Possibilities for insertion Kitchen unit with door Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. [. . . ]