User manual ZANUSSI ZHC9141

[. . . ] · The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose. Children should not be allowed to tamper with the controls or play with the appliance. During Use · This product is for domestic use only. · Never leave frying pans unattended during use as over-heated fats and oils might catch fire. · Do not leave naked flames under the hood. Maintenance and Service · This appliance can be a hazard if the synthetic paper and charcoal filters are not replaced as recommended. [. . . ] Never use excessive amounts of water when cleaning particularly around the control panel. Metal Grease Filters The grease filters absorb grease and dust during cooking to help keep the cooker hood clean inside, and should be cleaned approximately once every month or more often if the hood is used for more than 3 hours a day. Remove the metal grease filters one at a time by: Releasing the catches on the filters, the filters can be removed. The metal grease filters should be washed, by hand, in mild soapy water or in a dishwasher. Allow to dry completely before replacing. 6 Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned, we recommend they should be replaced approximately every three months or more often if the hood is used for more than three hours per day. To Remove/Replace the Charcoal Filters 1. Place the filter over the inlet grille at either end of the fan housing and rotate clockwise (A) into position. This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. 3. 4. Changing the Light Bulb 1. To replace the light bulb insert a replacement into the holder then rotate the bulb clockwise into position. Ensure you take care not to overtighten the bulb. 3. 4. If the light bulb fails to function check that the bulb is fully screwed into the holder. If bulb failure has occurred then it should be replaced with a 220-240 Volt 40W clear globe shaped bulb with a small E14 screw thread. Replacement filters and light bulbs can be obtained from your local Service Force Centre. 7 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · Check the hood is connected to the electricity supply. · The fan speed is set high enough for the task · The grease filter is clean. France Germany Italy Sweden UK Senlis Nurnberg Pordenone Stockholm Slough +33 (0)3 44 62 22 22 +49 (0)911 323 2600 +39 (0)1678 47053 +46 (0)20 78 77 50 +44 (0)1753 219 897 9 INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS HEIGHT OF CANOPY: HEIGHT OF CHIMNEY: (UPPER SECTION) (LOWER SECTION) WIDTH OF CANOPY - ZHC 613: WIDTH OF CANOPY - ZHC 913: DEPTH OF CANOPY: GROSS - ZHC 613: GROSS - ZHC 913: NET - ZHC 613: NET - ZHC 913: VOLTAGE: POWER CONSUMPTION: FAN MOTOR: LIGHT BULB: (2 x 40 W) 24cm 40cm 56cm 59, 8cm 89, 8cm 49cm 17kg 19, 3kg 13, 8kg 15, 9kg 220-240 V 50Hz 225W 145W 80W ELECTRICAL SUPPLY: SUITABLE FOR INSTALLATION ABOVE: ELECTRIC HOB: GAS HOB: SLOT-IN GAS COOKER SLOT-IN ELECTRIC COOKER 7KW (max) 10KW (max) 13. 5KW (max) 12. 4KW (max) Note: CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89:336. (Electromagnetic compatibility) and subsequent modifications and Low Voltage directive 72/23/E. ELECTRICAL CONNECTIONS This appliance must be earthed Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole. A minimum clearance height of 650mm (25 1/2 ") is required when installed above a built-in electric hob, or 700mm (27 1/2 ") when installed above a built-in gas hob. A minimum clearance height of 685mm (27") is required when installed above a slot-in electric cooker, or 787mm (30 1/2 ") when installed above a slot-in gas cooker. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm. If the height of the wall cabinet is less than 450mm, a gap of 50mm must be maintained either side of the hob. This cooker hood must not be installed above a cooking appliance with a high level grill. Hob A: Built-in Electric Hob: B: Built-in Gas hob: C: Slot-in Electric Cooker: D: Slot-in Gas Cooker: 650mm minimum clearance 700mm minimum clearance 685mm minimum clearance 787mm minimum clearance Fitting the Wall Brackets 1. Draw a vertical line on the wall from the centre of the cooking appliance up to the ceiling, using a spirit level and marking pen. Mark the centre positions for the lower bracket fixing screws (1) at 110mm either side of the vertical line (screws not supplied). [. . . ] When the electrical connection has been made, test the three speed fan and worktop illumination. 2. 3. 4. 5. 13 Venting The hood is more effective when used in the extraction mode (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of 125mm (5"). The 120-125mm collar should be fitted onto the ducting spigot to suit UK diameter ducting, and held in position by a jubilee clip (not supplied) used to secure the flexible hose. Where flexible duting is fitted the length should be no more than: 3 metres with one 90º bend, or 2metres with two 90º bends. [. . . ]