User manual ZANUSSI ZHC9744X

[. . . ] If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type. If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. · The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose. Do not install above a cooker with a high-level grill. · · · · Child Safety This appliance is designed to be operated by adults. Children should not be allowed to tamper with the appliance. · · · · During Use This product is for domestic use only. [. . . ] The charcoal filter cannot be cleaned or regenerated, and must be replaced approximately every 4 months, or more frequently if the hood is subjected to heavy usage. Remove the saturated activated charcoal filter by releasing the fixing hooks as illustrated. 5 Position the new charcoal filter in the position marked and while holding the filter replace the fixing hooks as illustrated. This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Changing the Spot Lamps Remove the two screws fixing the lighting support. Replace the spot lamp by inserting the two pins at the base of the lamp into the holes in holder and pushing into position. Replace the lighting support, ensuring it is located correctly and fix back into position using the two screws. If one of the spot lamps has failed to function check that the lamp is fully seated into the lamp holder. If lamp failure has occurred then it should be replaced with a 12V 20W M262 halogen spot lamp. Replacement filters and lamps can be obtained from your local Service Force Centre. 6 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 1 32121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 1 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 32121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · · · · · · · Check the hood is connected to the electricity supply. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting outlets are not blocked. The installation work must be undertaken by a qualified and competent person. The manufacturer disclaims any responsibility for damage due to incorrect installation of the cooker hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation. Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer's installation instructions. A minimum clearance height of 650mm (25½ins) is required when installed above a built-in electric hob, or 700mm (27½ins) when installed above a built-in gas hob. A minimum clearance height of 685mm (27ins) is required when installing above a slot-in electric cooker, or 787mm (30½ins) when installed above a slot-in cooker. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mmm (17¾ins), a gap of 50mm (2ins) must be maintained either side of the hob. This cooker hood must not be installed above a cooking appliance with a high level grill. The hood can be installed above these heights but for optimum performance it should be installed at the distances quoted for the appropriate heat source. 11 Drilling the Ceiling/Support Shelf Using a plumb line mark the centre point of the hob on the ceiling or support shelf. Position the drilling template item 21 on the ceiling or support shelf ensuring the template is aligned correctly with the angles of the hob. Pilot drill the fixing holes at the points marked for the approprate size rawl plugs and screws (not supplied). [. . . ] 13 Recirculation The cooker hood is supplied specified for use in the recirculation mode, with the charcoal filter fitted. In the recirculation mode contaminated air is passed through the charcoal filter to be purified and recirculated into the kitchen through the grille outlets on either side of the chimney. Recirculation Connection Assemble the two halves of the round recirculation extension duct 14. Push fit the assembled extesion duct 14 on to Ø150mm ducting spigot on top of the motor housing. Push fit the recirculation spigot 15 onto the other end of the extension duct 14. [. . . ]