User manual ZANUSSI ZKI245

[. . . ] User Manual Washerdryer Centrifugeren Centrifugeren Pompen Spoelen Inweken Inweken 30° Gordijnen Gordijnen 40° Sport Spor t 40° intensief Wol 40° Handwas Handwas 30° Handwas Handwas 40° 95° 60° eco 60° 40° 30° 60° 40° 30° 30° Anti-kreuk 40° 40° Anti-kreuk ZKI 245 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Content Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel and functions - - - - - - - - - - - -6 Programme table - - - - - - - - - - - - - - - - - -10 Washing and drying hints - - - - - - - - - - - - -12 Before the first use - - - - - - - - - - - - - - - - -14 Operating Sequence - - - - - - - - - - - - - - - -15 Washing only - - - - - - - - - - - - - - - - - - - - -15 Drying only and autodrying - - - - - - - - - - -17 2 Drying Times - - - - - - - - - - - - - - - - - - - - -18 Care and cleaning - - - - - - - - - - - - - - - - - -19 What to do if. . . [. . . ] Interrupting a programme Press the button 8 to interrupt a programme which is running, the corresponding light starts to flash. Cancelling a programme Turn the selector dial to «O» to cancel a programme which is running. Opening the door after the programme has started First set the machine to pause by pressing the button 8. If the light 9 goes off, the door can be opened immediately or after a few minutes depending on the model. If it does not switch off, this means that the machine is already heating or that the water level is too high. If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to «O». After a few minutes the door can be opened (Pay attention to the water level and temperature!). After this procedure, it will be necessary to set the programme and the options again and then to press button 8. Some acustic signals sound and on the display will appear a flashing «0 ». If at the end of a programme there is water in the tub, the light 9 remains on and the door is locked to indicate taht the door must be empty out. To empty out the water follow the following instructions: 1. at the end of programme, the display shows a flashing zero «0», the light 9 goes off and it will be possible to open the door. At the end of the cycle, turn the programme selector dial to «O» to switch the machine off. Remove the laundry from the drum and carefully check that the drum is empty. Leave the door open to prevent the formation of mildew and unpleasant smells. Drying only and autodrying (NON-STOP programme) The recommended load to dry in your washerdryer is 3 kg for cotton and 2 kg for synthetics. It is also possible to dry up to 4 kg of cotton items (see the drying time table). The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe. Turn the selector dial to «Cotton» or «Synthetics» programme in the «Drying» sector. Select the duration of the drying cycle by pressing repeatedly button 5 until the time you want appears on the display (see the drying programmes). For Cottons you can select a drying time from 10 minutes to 250 minutes (4. 10). For Synthetics you can select a drying time from 10 minutes to 130 minutes (2. 10). After the programme has started, the time remaining is updated every minute. At this point, begins an «anticrease phase», which lasts about 10 minutes. [. . . ] The hinges will be fixed to the door by means of screws for wood (2-Fig. c) Mounting the door Fix the hinges (1) to the machine by means of 29 416 818 120 820 min 176, 5 416 C 22+1 , 5 B 195 the M5x15 screws (3-Fig. The hinges can be adjusted to compensate for possible uneven thickness of the door. To align the door perfectly it is necessary to loosen the screw (3-Fig. [. . . ]