User manual ZANUSSI ZOU 363

[. . . ] Pour a little water into the dripping pan to avoid smoke and unpleasant smells. For hygiene and safety reasons, this appliance should be kept clean at all times. Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. This appliance is meant to operate with a singlephased connection to 230V electrical supply. [. . . ] 10. Oven thermostat control light Operation control light Oven function control knob Oven lamp Rating plate 3 Operation Oven function control knob (Fig. 1) The oven function control knob can have the following symbols and functions: 0 OFF position Oven light 50-250 Range of temperature regulation for conventional cooking - The heat comes from both the top and bottom element, ensuring even heating inside the oven Bottom heating element - The heat comes from the bottom of the oven only Top heating element - The heat comes from thetop of the oven only 0 100 5 0 25 0 Fig. 1 FO 2723 0 3 Hotplate control knobs The Control Knobs for the hotplates (Fig. The energy regulator of the hotplates can be set by means of a 7-position control knob: 0 = Off 1 = Minimum 3 = Maximum The intermediate positions give an increasing heating power. Carefully supervise cookings with oil or fats, since these types of food can result in a fire, when over-heated. Fig. 2 FO 2722 Thermostat control light (°C) Once the oven temperature has been selected, the temperature light will come on and remain on until the oven has reached the correct setting; after that, it will go on and off with the thermostat, showing how the temperature is being maintained. Oven control light It will come on every time an heating element (oven/ cooking plate) is set on operation. When the oven is first installed Before cooking for the first time, carefully wash the oven accessories. Once the oven has been installed: a) set the thermostat knob to MAX (250); b) allow the oven to run empty for approximately 45 minutes; c) open a window for ventilation. This is absolutely normal, and is caused by residues of manufacturing. Once this operation is carried out, let the oven cool down, then clean the oven cavity with a soft cloth soaked in warm soapy water. FO 2161 Fig. 3 To open the oven door, always catch the handle in its central part (Fig. 3). 4 200 2 15 0 1 Using the oven Always cook with the oven door closed. Conventional cooking Turn the oven function control knob to the required temperature (between 50 and 250°C). If cooking fruits, some over-heated natual acids can squeeze and settle on the oven enamel, causing stains quite difficult to remove. This could affect the enamel brightness, but it will have no consequence on the oven performances. To avoid these stains to be burnt out during the next cooking, carefully clean the oven cavity after all fruits cookings. The Oven Door and its gasket Before cleaning the oven door, we recommend you to remove it from the oven. Proceed as follows: a) open the oven door completely; b) find the hinges linking the door to the oven (fig. 6); c) unlock and turn the small levers located on the two hinges (fig. 6); d) handle the door by its left- and right-hand sides, then slowly turn it towards the oven until it is half-closed; e) gently pull the oven door off its site (fig. Once the cleaning is carried out, refit the oven door, following the procedure in reverse. Fig. 6 FO 0288 The correct operation of the oven is ensured by a gasket placed round the edge of the oven cavity. Do not use the oven until it has been repaired. 7 Something not working. . . If the appliance is not working correctly, please carry out the following checks, before contacting your local Service Centre. SYMPTOM n The oven does not come on SOLUTION uCheck that both a cooking function and a temperature have been selected or uCheck the appliance is wired in properly, and the socket switch or the switch from the mains supply to the oven are ON. uTurn the oven function control knob on a function or uBuy a new oven light bulb, asking for it to your local Service Centre and replace it by following the instruction provided in this booklet. uRefer to the contents of this booklet, especially to the chapter "Using the oven". [. . . ] The connection cable has to be placed in order that, in each part, it cannot reach a temperature 50 °C higher than the room temperature. After the connection is carried out, test the heating elements for about 3 minutes. Connection to terminal block This appliance is provided with a 6 poles terminal block (Fig. 10) set to operate with a 400 V three-phase electrical supply with neutral wire. To adapt the the terminal block to a different electrical supply, carry out the connection as shown in Fig. Once the connection is carried out, fit the cable into the the cable clamp. Fig. [. . . ]