User manual ZANUSSI ZWF1621

[. . . ] User Manual Libretto Istruzioni Washing Machine Lavabiancheria ZWF 1221 ZWF 1421 ZWF 1621 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Content Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel and functions - - - - - - - - - - - -6 Programme table - - - - - - - - - - - - - - - - - - -9 Programme information - - - - - - - - - - - - - -11 Washing Hints - - - - - - - - - - - - - - - - - - - - -12 Before the first use - - - - - - - - - - - - - - - - -14 Operating Sequence - - - - - - - - - - - - - - - -15 Care and cleaning - - - - - - - - - - - - - - - - - -18 What to do if. . . [. . . ] These must be selected after choosing the desired programme and before depressing the button 8. For the compatibility of the options with the washing programmes, refer to the section «Programmes table». Start the programme by pressing button 8 To start the selected programme, press this button; the corresponding green pilot light stops flashing. On programme progress display the pilot light DOOR illuminates to indicate that the appliance starts operating and the door is locked. If an option which is not compatible with the set wash programme is selected, the message Err is displayed for few seconds and the red light of this button flashes for 3 times. Pull out the dispenser drawer until it stops. Measure out the amount of detergent required, pour it into the main wash compartment and, if you wish to carry out a programme with the prewash phase or the soak programme, pour it into the compartment marked . If required, pour fabric softener into the compartment marked (the amount used must not exceed the «MAX» mark in the drawer). Select the required programme by means of the programme selector dial (1) Turn the programme selector dial to the required programme. The green light of button 8 starts to flash. It can be turned either clockwise or anticlockwise. On position «O» the programme is reset and the machine is switched OFF. At the end of the programme the selector dial must be turned to position «O», to switch the machine off. 15 Select the delayed start by pressing the button 10 Depress button this button to select the required delay. The selected delay time value will appear on the display for few seconds, then the duration of the programme will appear again. You must select this option after you have set the programme and before you press the button 5. You can cancel the delay time at any moment, before you press button 8. If you have already pressed it, and you wish to cancel the delay time, proceed as follows: · set the washing machine to PAUSE by pressing button 8; · press the button 10 once. · The selected delay can be modified only after you have turned the programme selector dial to the «o» position and after you have selected the programme again. If you need to open the door, you must first set the washing machine to PAUSE by pressing button 8 and wait few minutes before opening the door. The Delay Start cannot be selected with «Drain» programme. Display The display shows the following information: After selecting a programme the duration of the selected programme appears on the display. During the programme, the time remaining is updated every minute. 2. 00 The Delayed start appears on the display for about 3 seconds, then the duration of the previously selected programme is displayed. The delay time value decreases by one unit every hour and then, when 1 hour remain, every minute. The incorrect option selection is indicated by the message Err displayed for few seconds and by flashing of the light button 8. In the event of operating problems, some alarm codes can be displayed, (see paragraph "Something not working"). E20 The End of programme is indicated by a flashing zero «0». 0 16 Altering an option or a running programme It is possible to change any option before the programme carries it out. [. . . ] Water drainage The end of the drain hose can be positioned in three ways: Hooked over the edge of a sink using the plastic hose guide supplied with the machine. In this case, make sure the end cannot come unhooked when the machine is emptying. This could be done by tying it to the tap with a piece of string or attaching it to the wall. Water inlet An inlet hose is supplied and can been found inside the machine drum. Do not use the hose from your previous machine to connect to the water supply. [. . . ]