User manual ZANUSSI ZWH6125

[. . . ] User Manual Washing machine ZWH 6125 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Content Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel and functions - - - - - - - - - -6-7 Programme table - - - - - - - - - - - - - - - - -9-10 Programme information - - - - - - - - - - - - - -11 Washing Hints - - - - - - - - - - - - - - - - - - - - -12 Before the first use - - - - - - - - - - - - - - - - -14 Operating Sequence - - - - - - - - - - - - - - - -15 Care and cleaning - - - - - - - - - - - - - - - - - -18 Something not working - - - - - - - - - - - - - - 20 Technical data- - - - - - - - - - - - - - - - - - - - - 23 Consumption values - - - - - - - - - - - - - - - - 24 Installation instruction - - - - - - - - - - - - - - - 25 Environmental concerns - - - - - - - - - - - - - 28 Guarantee conditions - - - - - - - - - - - - - - - 29 European guarantee - - - - - - - - - - - - - - - - 30 2 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. [. . . ] If an option which is not compatible with the set wash programme is selected, the message Err is displayed for few seconds and the red light of this button flashes for 3 times. Measure out the amount of detergent required, pour it into the main wash compartment and, if you wish to carry out a programme with the prewash phase or the soak programme, pour it into the compartment marked . If required, pour fabric softener into the compartment marked (the amount used must not exceed the «MAX» mark in the drawer). Select the required programme by means of the programme selector dial (1) Turn the programme selector dial to the required programme. The green light of button 8 starts to flash. It can be turned either clockwise or anticlockwise. On position «O» the programme is reset and the machine is switched OFF. At the end of the programme the selector dial must be turned to position «O», to switch the machine off. Select the delayed start by pressing the button 10 Depress button this button to select the required delay. The selected delay time value will appear on the display for few seconds, then the duration of the programme will appear again. You must select this option after you have set the programme and before you press the button 5. You can cancel the delay time at any moment, before you press button 8. If you have already pressed it, and you wish to cancel the delay time, proceed as follows: · set the washing machine to PAUSE by pressing button 8; · press the button 10 once. · The selected delay can be modified only after you have turned the programme selector dial to the «o» position and after you have selected the programme again. If you need to open the door, you must first set the washing machine to PAUSE by pressing button 8 and wait few minutes before opening the door. The Delay Start cannot be selected with «Drain» programme. Display The display shows the following information: After selecting a programme the duration of the selected programme appears on the display. During the programme, the time remaining is updated every minute. 2. 00 The Delayed start appears on the display for about 3 seconds, then the duration of the previously selected programme is displayed. The delay time value decreases by one unit every hour and then, when 1 hour remain, every minute. The incorrect option selection is indicated by the message Err displayed for few seconds and by flashing of the light button 8. In the event of operating problems, some alarm codes can be displayed, (see paragraph "Something not working"). E20 The End of programme is indicated by a flashing zero «0». 0 16 Altering an option or a running programme It is possible to change any option before the programme carries it out. Before you make any change, you must pause the washing machine by pressing button 8. Turn the programme selector dial to «O» and then to the new programme position. Interrupting a programme Depress tbutton 8 to interrupt a programme which is running, the corresponding light starts to flash. Cancelling a programme Turn the selector dial to «O» to cancel a programme which is running. [. . . ] The drain hose must not be kinked. Electrical connection This machine is designed to operate on a 220230 V, single-phase, 50 Hz supply. Check that your domestic electrical installation can take the maximum load required (2. 2 kW), also taking into account any other appliances in use. The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution. Should the appliance power supply cable need to be replaced, this should be carried out by our Service Centre. [. . . ]