User manual ZANUSSI ZX6631S

[. . . ] Ensure a continuous air supply, keeping the air vents in good conditions or installing a cooker hood with discharge tube. In case of intensive or long time use of the appliance, make the ventilation more efficient, by opening a window or increasing the electric exhaust fan power. Once you removed all packaging from the appliance, ensure that it is not damaged and the electric cable is in perfect conditions. Otherwise, contact your dealer before proceeding with the installation. [. . . ] If you cannot light the flame even after several attempts, check the "cap" (Fig. · Always turn the flame down or put it out before taking the pans off the burner. 1 FO 0204 USING THE HOB CORRECTLY To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside). It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. Burner minimum diameter 160 mm. 160 mm. Big (double crown) Medium (semirapid) Small (Auxiliary) 3 POTTERY Remember that a wide-bottomed pan allows a faster cooking than a narrow one. Particularly make sure that the pans are not too small for liquids, since these could easily overflow. In fact, an openable mould lets juices and sugar leak through, falling on the bottom of the oven and consequently burning on the bottom of the baking tray, making cleaning difficult. Avoid putting plastic-handled pans in the oven as they are not heat-proof. You should use oans with the right diameter to fit the burner, in order to make the most out of it, thus reducing gas consumption as in Fig. It is also advisable to cover any boiling casserole and, as soon as the liquid starts boiling, lower the flame enough to keep the boiling point. HOTPLATES The hotplates control knob can be adjusted on six different positions, according to your cooking needs, from maximun heat (position 6) to minimum heat (position 1), as shown in Fig. 3. 0 6 1 5 2 Saucepans suitable for use on solid plate hobs should have several characteristics: · · · they should be fairly heavy duty; they should fit the heat area exactly, or be slightly larger for efficient use, NEVER smaller; they should have a flat base to ensure good contact with the plate (see Fig. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut GJ 1/2". Screw the parts without forcing, adjust the connection in the required direction and tighten everything. IMPORTANT - When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Use some soapy water, never a flame. A) Ramp with ending nut B) Seal C) Adjustable connection FO 0264 Fig. Electrical Connection The appliance is designed to be connected to 230 V ~ 50 Hz electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. This has to be provided with a proper plug, able to support the load marked on the identification plate. If connecting the appliance directly to the electric system, it is necessary that you install a double pole switch between the appliance and the electricity supply, with a minimum gap of 3 mm. [. . . ] 6 FO 0392 Should the feeding gas pressure be different or variable compared with the required pressure, an appropriate pressure adjuster must be fitted on the gas supply pipe, in compliance with the rules in force. ADJUSTMENT OF MINIMUM LEVEL To adjust the minimum level of the burners, proceed as follows: · Light the burner. · With a thin screwdriver, adjust the by-pass screw positioned beside or inside the tap rod (see Fig. If changing from natural gas to LPG, completely tighten clockwise the screw. When converting from LPG to natural gas unscrew about one-fourth turn by-pass pin. [. . . ]