User manual ZIBRO R 21 E

[. . . ] R 20 E / R 21 E / R 31 E 3 2 5 FIN MANUEL D'UTILISATION GEBRAUCHSANWEISUNG INSTRUCCIONES DE USO KYTTOHJE OPERATING MANUAL ISTRUZIONI D'USO BRUKSANVISNING GEBRUIKSAANWIJZING BRUKSANVISNING 2 14 26 38 50 62 74 86 98 4 > u 1 = # 1-3 cm. # R Dear Sir, Madam, Congratulations on your purchase of this Zibro heater, the number one brand amongst portable heaters. You have purchased a first-class quality product, which will serve you for many years to come. Please read these Directions for Use first, to ensure the maximum lifetime for your Zibro heater. This appliance comes with a 24-month manufacturer's warranty on all defects in material or workmanship. We wish you much warmth and comfort from your Zibro heater. Yours sincerely, PVG International b. v. [. . . ] If the heater has been used only a few times and the wick adjustment knob is not locked, first turn the wick adjustment knob (Fig. L) completely left, before putting the wick in the highest position for ignition (Section C). 4 54 E After having ignited the heater, always check whether the combustion D L chamber is level, by sliding it slightly to the left and the right by its handle (Fig. If the combustion chamber is not level, this will cause smoke and soot to develop. BURNING OF THE HEATER After you have ignited the heater, it will take 10 to 15 minutes before you can check whether the heater is burning well. Too high a flame may cause smoke and soot, whereas too low a flame causes smells. The page opposite the folding page shows the minimum and maximum permissible burning heights of the flame (Fig. R). M VENT. If the flame remains low after the adjustment, the wick height must be adjusted (refer to Section F). Burning that is too low may be caused by: insufficient fuel poor fuel quality insufficient ventilation wastage of the wick (fill the tank) (contact your dealer) (put window or door ajar) (contact your dealer or replace the wick, refer to section M) When there is insufficient ventilation in the room, an intermittent buzzer will be heard and the VENT lamp (Yellow) will be lit. When this signal is given, ensure that the ventilation of the room is improved (e. g. by opening a door or window a little more) to avoid that the heater shuts off. When the ventilation of the room is improved, the VENT lamp and buzzer will be deactivated. When there is still insufficient ventilation, the heater shuts off automatically. by opening a door or window a little more), the heater can be ignited again. This heater is fitted with a safety system that ensures that it switches off if you lift the exchange tank out of the heater. To switch the heater on again, put the exchange tank back and follow the steps in chapter C. E F N SWITCHING OFF THE HEATER Push the OFF-button . The flame will extinguish after a little while. ADJUSTING THE WICK HEIGHT (R21E) After a period of time the combustion may no longer be high enough (Section D). 2 Pull the knurled wick adjustment knob off the heater, so the wick height lock will be visible. 3 Take the plastic collar between your thumb and index finger and pull it out. Carefully push the collar back, so the pin engages in the recess. O 4 55 4 Carefully reinstall the knurled wick adjustment knob. This can be done in one way only - check the rear of the cap for the correct position. F If adjustment of the wick height does not have the required effect, let the heater burn until all fuel has been used up (Section H). If the flame height is still too low and the wick is set on position 3, then contact your dealer, or replace the wick, refer to section M. If the flame gets too high after adjusting (Fig R), the wick height lock should be placed one position lower again. Otherwise smoke or soot may be caused. G MALFUNCTION, CAUSES AND SOLUTIONS If any malfunctioning cannot be solved from the directions below, please contact your dealer. [. . . ] Always store the fuel in a cool, dry and dark place (sunlight will affect the quality). Never use the heater in places where harmful gasses or fumes may be present (e. g. Always make sure that there is sufficient ventilation. 8 9 10 4 59 1 2 REPLACEMENT OF THE WICK M 3 4 ENSURE THAT THE HEATER IS OFF AND COMPLETELY COOL BEFORE STARTING TO REPLACE THE WICK. 1 Open the lid and remove the removable tank. 4 Pull the knurled wick adjustment knob off the heater (wick height lock: R21E). [. . . ]